Ounting The Impeller - Onean Carver X User Manual

07
R
epaiRs and
7.1.2. M

ounting the iMPeLLer

1. Hold the tool (7) next
to the impeller (A)and
screw the 3 socket head
screws (2) using the hex
key SW2,5 . The tool and
impeller will be fixed to
one another as you may
see in the picture below.
"assembly 1".
Assembling a new impeller to the water
pump:
assembly 1
I) Hold the tool (1) next to the impeller (A) and screw the three screws (3)
until the end with the allen key SW2,5 provided in the tooling box, building
the assembly (I)
A
Disassembling the nozzle from the jet:
Unscrew the five screws DIN 912 m4x12 to the Jet´s housing, hold the nozzle and
pull manualy the assembly out of its shaft.
24
CARVER USER'S MANUAL
R
eplacements
2. Manually introduce the
assembly 1 to the Jet Unit
through the shaft (B) as
far as possible without
applying excessive force
3. Screw knurled nut (3) to
the threaded rod (1) with
the hexagon domed cap
(8) and introduce the flat
washer (4) creating the
"assembly 2".
II) Introduce manually the assembly (I) into the shaft (B) as far as possible without applying too
much force.
Screw the knurled knob (5) to the threaded rod with cap (2) and mount the washer (6) building
Assembling a new impeller to the water
II) Introduce manually the assembly (I) into the shaft (B) as far as possible without applying too
the assembly (II).
much force.
pump:
Introduce the assembly (II) through the assembly (I) and screw the assembly (II) to the pump´s Screw the knurled knob (5) to the threaded rod with cap (2) and mount the washer (6) building
the assembly (II).
shaft (B).
Introduce the assembly (II) through the assembly (I) and screw the assembly (II) to the pump´s
shaft (B).
I) Hold the tool (1) next to the impeller (A) and screw the three screws (3)
until the end with the allen key SW2,5 provided in the tooling box, building
the assembly (I)
Disassembling the nozzle from the jet:
Unscrew the five screws DIN 912 m4x12 to the Jet´s housing, hold the nozzle and
B
pull manualy the assembly out of its shaft.
assembly 2
Detaching the impeller from the water pump:
I) Unmount the Circlip (C) and screw the hexagonal head screw (7)
into the pump shaft (A).
4. Pass the assembly 2
through the tool's (7) hole
and screw the threaded
rod (1) to the JetUnit's
shaft (B) holding it from
the hex cap (8).
5. Hold the tool (7) while
turning the knurled nut (3)
clockwise. The assembly
1 & 2 while slightly mount
onthe the Jetpack's Shaft (B).
III) Turn the knurled knob (5) while holding the tool (1) with the
hands until the end.
III) Turn the knurled knob (5) while holding the tool (1) with the
hands until the end.
Detaching the impeller from the water pump:
II) Hold the tool (1) next to the impeller while screwing the three
I) Unmount the Circlip (C) and screw the hexagonal head screw (7)
screws (3) until the end with the allen key SW2,5 provided in the
into the pump shaft (A).
tooling box.
Manually screw the socket set screw (8) to the impeller tool until
the end (until it touches the hexagonal screw (3).
II) Hold the tool (1) next to the impeller while screwing the three
screws (3) until the end with the allen key SW2,5 provided in the
tooling box.
Manually screw the socket set screw (8) to the impeller tool until
the end (until it touches the hexagonal screw (3).
6. Once the Impeller reaches 8. In order to mount the
the end of its trayectory,
unscrew the assembly 2
from the shaft (B) holding it
from the hexagonal cap (8).
7. Unscrew the tool from
the impeller.
IV) Detach the mounting tool by unscrewing the knurled knob,
screws and threaded rod. Mount the circlip (C).
IV) Detach the mounting tool by unscrewing the knurled knob,
screws and threaded rod. Mount the circlip (C).
B
III) Screw the socket set screw while holding the tool (1) with the
SW3 wrench provided in the tool box.
III) Screw the socket set screw while holding the tool (1) with the
SW3 wrench provided in the tool box.
Stator/Nozzle assembly
back to the Jet Unit, it is
recommended to apply
grease on the Jet Unit's
shaft. Push the assembly
Stator/Nozzle onto the
shaft and screw the 5
socket head screws using
the hex key SW3.
Apply grease
Assembling the nozzle to the jet:
If available, apply some grease to the shaft´s top at first.
Assembling the nozzle to the jet:
Push the Stator-Nozzle assembly into the Pumps shaft (B) and screw the five
screws DIN 912 m4x12 to the Jet´s housing.
If available, apply some grease to the shaft´s top at first.
Push the Stator-Nozzle assembly into the Pumps shaft (B) and screw the five
screws DIN 912 m4x12 to the Jet´s housing.
B D
ToolBox
SW 13-14 T-wrench
1x Allen key SW3
1x Allen key SW2,5
ToolBox
SW 13-14 T-wrench
1x Allen key SW3
1x Allen key SW2,5