Table of Contents
Advertisement
7.
rePair and rePLaceMent oF coMPonentS
Clean the board with fresh water after every use. Introduce grease into the
stator bearings through the greasing screw periodically. Keep the battery
power connectors dry and clean.
Assembling a new impeller to the water
7.1. i
pump:
MPeLLer
Always manipulate the impeller with extreme caution as its sharp edges could
I) Hold the tool (1) next to the impeller (A) and screw the three screws (3)
until the end with the allen key SW2,5 provided in the tooling box, building
cause injuries.
the assembly (I)
Item
File Name (no extension)
Do never activate the board while replacing the impeller as it could cause
Number
damage to the JetPack.
1
din_976_m4x65_A2
2
din_en_iso_4762_m3x30
7.1.1. u
nMounting the iMPeLLer
3
din_466_m4_0_5
Next you may find a detailed explanation on how to unmount and mount the
4
din125-1-a_4_3-140_hv
impeller. On our website you may find additional tutorial videos serving the
5
screw_din_933-m4x6-10_9
-a
same purpose.
6
din_913-m6x50-45h
7
unmount_tool_s
1. Unscrew the 5 screws on the
8
din1587-m4x0_76
Jet Unit's outer surface using
the hex key SW3 and extract
the
Stator/Nozzle
assembly.
Disassembling the nozzle from the jet:
Unscrew the five screws DIN 912 m4x12 to the Jet´s housing, hold the nozzle and
B
pull manualy the assembly out of its shaft.
II) Introduce manually the assembly (I) into the shaft (B) as far as possible without applying too
much force.
Screw the knurled knob (5) to the threaded rod with cap (2) and mount the washer (6) building
the assembly (II).
Introduce the assembly (II) through the assembly (I) and screw the assembly (II) to the pump´s
shaft (B).
Item
File Name (no extension)
Quantity Material
Quantity Material
Number
1
din_976_m4x65_A2
1
Stainless Steel
1
Stainless Steel
2
din_en_iso_4762_m3x30
3
Stainless Steel
3
Stainless Steel
3
din_466_m4_0_5
1
Stainless Steel
1
Stainless Steel
4
din125-1-a_4_3-140_hv
1
Stainless Steel
1
Stainless Steel
5
screw_din_933-m4x6-10_9
1
Stainless Steel
1
Stainless Steel
-a
6
din_913-m6x50-45h
1
Stainless Steel
1
Stainless Steel
7
unmount_tool_s
1
Anodized tempered Aluminum
1
Anodized tempered Aluminum
8
din1587-m4x0_76
1
Stainless Steel
1
Stainless Steel
2. Unmount the Circlip (Seeger Ring)
(C) and screw the hex screw (5) to
the Jet Unit's shaft (B).
Detaching the impeller from the water pump:
B
I) Unmount the Circlip (C) and screw the hexagonal head screw (7)
into the pump shaft (A).
Impeller tool
Impeller tooling kit
(5)
Impeller tool (7)
III) Turn the knurled knob (5) while holding the tool (1) with the
hands until the end.
3. Hold the impeller tool (7) next
to the impeller (A) and screw
the 3 socket cap screws (2)
until the end using the hex
key SW2,5. Manually screw the
set screw (6) to the tool (7).
II) Hold the tool (1) next to the impeller while screwing the three
screws (3) until the end with the allen key SW2,5 provided in the
C
tooling box.
Manually screw the socket set screw (8) to the impeller tool until
the end (until it touches the hexagonal screw (3).
R
R
epaiRs and
eplacements
Impeller tool (7)
IV) Detach the mounting tool by unscrewing the knurled knob,
2
screws and threaded rod. Mount the circlip (C).
2
4
6
1
4. While holding the tool, screw the
set screw (6) using the hex key
SW3. You will see the impeller (A)
moving out of the Jet unit while
screwing the set screw (6).
III) Screw the socket set screw while holding the tool (1) with the
SW3 wrench provided in the tool box.
A
CARVER USER'S MANUAL
07
Assembling the n
If available, apply some grease
Push the Stator-Nozzle assemb
screws DIN 912 m4x12 to the Je
3
8
23
Advertisement
Table of Contents
