Related Manuals for Danfoss 180F4161
Summary of Contents for Danfoss 180F4161
- Page 1 Service guide Vane pump upgrade kit 180F4161 iSave 21 ERD Disassembling and assembling hpp.danfoss.com...
-
Page 2: Table Of Contents
Parts included in the vane pump upgrade kit 180F4161 ....... . -
Page 3: Disassembling The Isave
Service guide | Disassembling and assembling iSave 21 vane pump with upgrade kit 180F4161 Disassembling the iSave Place the iSave on a clean table. Unscrew the bolts in the flange. Remove the vane pump. 180R9402 | 521B1455 | DKCFN.PI.003.T1.02 | 10.2017... -
Page 4: Disassembling The Vane Pump
Service guide | Disassembling and assembling iSave 21 vane pump with upgrade kit 180F4161 Disassembling the vane pump Gently adjust the spanner wrench around Unscrew the bolt in the middle of the the coupling and use it as back stop. - Page 5 Service guide | Disassembling and assembling iSave 21 vane pump with upgrade kit 180F4161 Gently remove the rotor. Remove vanes. Note: Loose parts inside the rotor. Gently remove side plate and pin. Remove the int. flange 180R9402 | 521B1455 | DKCFN.PI.003.T1.02 | 10.2017...
-
Page 6: Assembling The Vane Pump - With Parts From The Vane Pump Upgrade Kit
Service guide | Disassembling and assembling iSave 21 vane pump with upgrade kit 180F4161 Assembling the vane pump - with parts from the vane pump upgrade kit Place the new O-ring and guide pin in Place the new side plate on the int. - Page 7 Service guide | Disassembling and assembling iSave 21 vane pump with upgrade kit 180F4161 Position the 8 new vanes in the rotor. Gently place the rotor in the bearing. The pins may be moved by using a screwdriver. Check that all vanes are positioned One vane is NOT positioned correctly.
- Page 8 Service guide | Disassembling and assembling iSave 21 vane pump with upgrade kit 180F4161 Make sure that the new guide pin is located Place the pump housing with the pin in the locating hole in the side plate. See orientated upwards. Fit the flange #12.
-
Page 9: Assembling The Isave
Service guide | Disassembling and assembling iSave 21 vane pump with upgrade kit 180F4161 Install the 2 new labels on top of each Change the two new O-rings in the product label to cover the old code no. as flange. -
Page 10: Exploded View Vane Pump
Service guide | Disassembling and assembling iSave 21 vane pump with upgrade kit 180F4161 Exploded view vane pump 180R9402 | 521B1455 | DKCFN.PI.003.T1.02 | 10.2017... -
Page 11: Exploded View Isave
Service guide | Disassembling and assembling iSave 21 vane pump with upgrade kit 180F4161 Exploded view iSave 180R9402 | 521B1455 | DKCFN.PI.003.T1.02 | 10.2017... - Page 12 Danfoss A/S High Pressure Pump Nordborgvej 81 DK-6430 Nordborg Denmark © Danfoss | DCS (im) | 2017.10 180R9402 | 521B1455 | DKCFN.PI.003.T1.02 | 06 | 12...