Related Manuals for KanexPro WP-2X1HDUSBC
Summary of Contents for KanexPro WP-2X1HDUSBC
- Page 1 WP-2X1HDUSBC Double Gang 4K HDMI 2.0 & USB-C Wall plate Extender & Switcher over HDBaseT™ w/ IR & PoH All Rights Reserved Version: WP-2X1HDUSBC_2019V1.0...
- Page 2 3x1 Wall plate Extender & Switcher Preface Read this user manual carefully before using the product. Pictures shown in this manual are for reference only. Different models and specifications are subject to real product. This manual is only for operation instruction, please contact the local distributor for maintenance assistance.
- Page 3 3x1 Wall plate Extender & Switcher SAFETY PRECAUTIONS To ensure the best performance from the product, please read all instructions carefully before using the device. Save this manual for further reference. Unpack the equipment carefully and save the original box and packing material for ⚫...
-
Page 4: Table Of Contents
3x1 Wall plate Extender & Switcher Table of Content Product Introduction ......................1 1.1 Features ......................2 1.2 Package List ....................... 3 2. Specification ........................ 4 3. Panel Description ......................5 3.1 Front Panel ......................5 3.2 Rear Panel ......................6 4. -
Page 5: Product Introduction
3x1 Wall plate Extender & Switcher Introduction The KanexPro WP-2XHDUSBC is a US Decora style double-gang, 3x1 Wall plate transmitter and switcher designed to switch two HDMI®2.0 inputs and one USB-C input to a remote display or a projector up to 131ft.(40m) at 4K/60 and 230ft.(70m) at 1080p/60 video and audio over single cat5e/6/7 cable. -
Page 6: Features
3x1 Wall plate Extender & Switcher 1.1 Features ▪ US Decora Style, Double-Gang HDMI® 2.0 & USB-c wall plate over HDBaseT™ ▪ Supports HDMI signal up to 4K@60Hz 4:4:4, ▪ USB-C video signal up to 4K@30Hz 4:4:4. ▪ EDID & HDCP 2.2 compliant ▪... -
Page 7: Package List
3x 2-pin Terminal Block ⚫ 1x 3-pin Terminal Block ⚫ 1x Power Adapter (24V 1.25A) ⚫ 1x User Manual ⚫ Note: Please contact KanexPro at support@kanexpro.com or your distributor immediately if any damage or defect in the components is found. -
Page 8: Specification
3x1 Wall plate Extender & Switcher with HDMI 2.0 and USB-C 2. Specification Input Input (2) HDMI, (1) USB-C (Slimport) Input Connector (2) Type-A female HDMI, (1) USB-C HDMI Input Resolution Up to 4K@60Hz 4:4:4 Slimport Input Resolution Up to 4K@30Hz 4:4:4 Output Output (1) HDBT OUT... -
Page 9: Panel Description
3x1 Wall plate Extender & Switcher with HDMI 2.0 and USB-C 3. Panel Description 3.1 Front Panel LINK RESET SOURCE/AUTO HDMI IN 1 DISPLAY ON/OFF HDMI IN 2 USB-C IN FIRMWARE ① LINK LED: The LED illuminates green when the transmitter is successfully connected to the receiver by a CATx cable. -
Page 10: Rear Panel
3x1 Wall plate Extender & Switcher with HDMI 2.0 and USB-C ⑪ USB-C: Type-C USB to connect the MacBook or other device with USB-C output. ⑩ FIRMWARE: Micro-USB port for firmware upgrade. ⑫ USB-C LED: The LED illuminates orange when the USB-C port is connected to a ⑬... -
Page 11: System Connection
3x1 Wall plate Extender & Switcher with HDMI 2.0 and USB-C 4. System Connection Usage Precautions Make sure all components and accessories included before installation. ⚫ System should be installed in a clean environment with proper temperature and ⚫ humidity. All of the power switches, plugs, sockets, and power cords should be insulated and ⚫... -
Page 12: Button Control
3x1 Wall plate Extender & Switcher with HDMI 2.0 and USB-C 5. Button Control 5.1 Source Switching 1) Press the SOURCE AUTO button to switch to next source device, and then the corresponding input LED will turn green. 2) Press and hold the SOURCE AUTO button at least 3 seconds to enable auto switching mode, and it abides by the following principles: The switcher will switch to the first available active input starting at HDMI IN 1>... -
Page 13: Rs232 Control
3x1 Wall plate Extender & Switcher with HDMI 2.0 and USB-C 6. RS232 Control 6.1 RS232 Connection According the RS232 control mode, there are three types of RS232 connection for different application. ① To control the switcher from local, please connect a control device (e.g. PC) to the RS232 port of the switcher, the connection diagram shown as below: Transmitter Switcher... - Page 14 3x1 Wall plate Extender & Switcher with HDMI 2.0 and USB-C ② To control the switcher from remote, please connect a control device (e.g. PC) to the RS232 port of the remote receiver, the connection diagram shown as below: Transmitter Switcher RS232 Receiver CATx Cable:...
- Page 15 3x1 Wall plate Extender & Switcher with HDMI 2.0 and USB-C ③ To control the far-end third party device, please connect the control device (e.g. PC) to the RS232 port of the switcher, and then please connect the third party device (e.g.
-
Page 16: Rs232 Control Software
3x1 Wall plate Extender & Switcher with HDMI 2.0 and USB-C 6.2 RS232 Control Software After set all needed input and output devices according to the RS232 connection diagram, please install the RS232 control software into the control PC to send RS232 command. -
Page 17: Rs232 Command
3x1 Wall plate Extender & Switcher with HDMI 2.0 and USB-C Please set the parameters of COM number, bound rate, data bit, stop bit and the parity bit correctly, then the RS232 commands can be sent in the Command Sending Area. Baud rate: 9600. -
Page 18: Source Switching
3x1 Wall plate Extender & Switcher with HDMI 2.0 and USB-C 6.3.2 Source Switching Command Function Feedback Example #SET_AV H1 Switch to HDMI 1. @AV H1 #SET_AV H2 Switch to HDMI 2. @AV H2 #SET_AV C Switch to USB-C. @AV C @AV H1 #GET_AV Get the current input source. -
Page 19: Edid Management
3x1 Wall plate Extender & Switcher with HDMI 2.0 and USB-C 6.3.5 EDID Management The input resolution (EDID setting) can be set using RS232 commands to one of the options given in the following table. Command Function Feedback Example #SET_EDID_MODE 0 EDID bypass. -
Page 20: Button User-Defined
3x1 Wall plate Extender & Switcher with HDMI 2.0 and USB-C 7. Button User-defined Press the DISPLAY ON/OFF button can turn on/off the display. If the incompatible display device needs to be used, the DISPLAY ON/OFF button can be programed by IR learning feature or RS232 command. - Page 21 3x1 Wall plate Extender & Switcher with HDMI 2.0 and USB-C Programed by RS232 command: ⚫ The DISPLAY ON/OFF button also can be defined to send control characters by following the below command format. Command Function Feedback Example Automatically send the command "xxxx" to the #SET_ON_05_30:12345 third-party device while the DISPLAY ON key has been pressed.
-
Page 22: Panel Drawing
3x1 Wall plate Extender & Switcher with HDMI 2.0 and USB-C 8. Panel Drawing 89.0 mm LINK RESET SOURCE/AUTO HDMI IN 1 DISPLAY ON/OFF HDMI IN 2 USB-C IN FIRMWARE... -
Page 23: Troubleshooting & Maintenance
3x1 Wall plate Extender & Switcher with HDMI 2.0 and USB-C 9. Troubleshooting & Maintenance Problems Potential Causes Solutions Color losing or no video signal output on the HDMI display. The cables may be not Check the cables are No HDMI signal output in connected correctly or properly connected and the device while local... -
Page 24: Customer Service
3x1 Wall plate Extender & Switcher with HDMI 2.0 and USB-C 10. Customer Service The return of a product to our Customer Service implies the full agreement of the terms and conditions hereinafter. There terms and conditions may be changed without prior notice.