Table of Contents
Advertisement
Quick Links
UM_201709_PL21_011
COOLDIM_PRG_BOARD
User manual for CDM10V programming board
About this document
Scope and purpose
CDM10V programming user manual describes the "COOLDIM_PRG_BOARD" burner board usage, the UART
protocol handling and the fusing details.
Intended audience
CDM10V programming board user.
Table of contents
About this document ....................................................................................................................... 1
Table of contents ............................................................................................................................ 1
1
CDM10V BURNER .................................................................................................................... 2
1.1
Introduction ............................................................................................................................................. 2
1.2
Chip orientation ...................................................................................................................................... 2
1.3
Control buttons ....................................................................................................................................... 3
1.4
Switches ................................................................................................................................................... 3
1.5
Connectors / Jumper .............................................................................................................................. 4
2
Fusing details ........................................................................................................................ 5
2.1
UART configuration ................................................................................................................................. 5
2.2
Fusing conditions .................................................................................................................................... 5
2.3
Fusing procedure .................................................................................................................................... 6
Revision history ............................................................................................................................. 8
User Manual
www.infineon.com
Please read the Important Notice and Warnings at the end of this document
page 1 of 9
V 1.0
2017-09-19
Advertisement
Table of Contents
Related Manuals for Infineon CDM10V
Summary of Contents for Infineon CDM10V
-
Page 1: Table Of Contents
COOLDIM_PRG_BOARD User manual for CDM10V programming board About this document Scope and purpose CDM10V programming user manual describes the “COOLDIM_PRG_BOARD” burner board usage, the UART protocol handling and the fusing details. Intended audience CDM10V programming board user. Table of contents About this document ........................ -
Page 2: Cdm10V Burner
Introduction The COOLDIM_PRG_BOARD is used to set fuses inside CDM10V chip. It is supplied from a USB power supply (5 V / 1 A) or could also be connected to a USB port of the PC. User will be guided through the burning process by the microcontroller firmware. -
Page 3: Control Buttons
COOLDIM_PRG_BOARD User manual for CDM10V programming board CDM10V BURNER Control buttons ON/OFF Check if chip is applied in correct position and turn supply voltage on or off. When supply is turned on all 4 parameters are measured and shown in display. If one parameter could not be measured a contact fail is expected supply is turned off and the user is informed to check the socket. -
Page 4: Connectors / Jumper
COOLDIM_PRG_BOARD User manual for CDM10V programming board CDM10V BURNER Connectors / Jumper Optional connectors for external socket board. Figure 3 Connectors User Manual 4 of 9 V 1.0 2017-09-19... -
Page 5: Fusing Details
COOLDIM_PRG_BOARD User manual for CDM10V programming board Fusing details Fusing details UART configuration The serial port (9600 Baud, 1 stop bit, no parity) enables a onetime reconfiguration of parameters for device function. The reserved CMD bit has to be set to HIGH. After this bit the 7 programming has to be sent in the order shown in the picture below. -
Page 6: Fusing Procedure
COOLDIM_PRG_BOARD User manual for CDM10V programming board Fusing details Fusing procedure To ensure the correct efuse burning automatic programming and checking procedure is implemented. Remark that fusing can be done one time only per device. IDLE UART commad received FUSE... - Page 7 COOLDIM_PRG_BOARD User manual for CDM10V programming board Fusing details DONE If the compared data it correct the I is set to HIGH if not this will say in LOW in this state. Remark that the power down/up step is required to return to the normal operation after the whole efuse burning procedure is performed.
-
Page 8: Revision History
COOLDIM_PRG_BOARD User manual for CDM10V programming board Fusing details Revision history Document Date of release Description of changes version User Manual 8 of 9 V 1.0 2017-09-19... - Page 9 Do you have a question about this Except as otherwise explicitly approved by Infineon information given in this application note. Technologies in a written document signed by...