Setting Functions In Set Mode - Omron E3X-DAC-S Series Manual

Setting Functions in SET Mode

5
Function Transitions
➜
Page 20
Refer to 2. Registering Workpiece
Colors with Teaching in SET Mode.
Teaching
Set the SET/RUN
Mode Selector to SET.
SET
Judgment mode
(Used to set the judgment
mode)
Functions
Use the UP and DOWN Keys to change the settings.
Function
Operation mode Match: ON
Super-high-speed:
Standard:
Detection
Note: If the detection function is changed, be sure to
teach the workpiece color.
Enabled:
Timer
ON-delay timer:
1 to 5000 ms:
Timer time
(timer enabled) (1 to 20: 1-ms increments, 20 to 200 ms: 5-ms increments,
200 to 1000: 100-ms increments, 1000 to 5000: 1000-ms increments)
1-point teaching:
MODE key Zero-shift reset:
➜
Page 22 Refer to 6-1. Zeroing the Display (Zero Reset).
Teaching level 0 to 99P:
(1) Match/threshold:
(2) Margin/threshold:
(3) Peak/Bottom refreshed every 2 s:
(4) Peak/Bottom refreshed every time the output is switched:
Display switch
(5) Analog bar display:
(6) Match/peak (updated periodically):
(7) Match/channel:
Display orientation
Normal display:
Output setting Each channel:
Enabled:
Timer function
ON-delay timer:
1 to 5000 ms:
Timer time
(1 to 20: 1-ms increments, 20 to 200 ms: 5-ms increments,
200 to 1000: 100-ms increments, 1000 to 5000: 1000-ms increments)
1-point teaching:
External input
Zero-shift reset:
External input memory
Write: , Do not write:
C/I automatic judgment:
Judgment mode
BLACK mode:
*
Operation mode
(To set the operation mode)
External input memory
(Refer to instructions
provided with the product.)
Settings (display)
, Mismatch:
, High-speed: ,
, High-resolution:
, OFF-delay timer:
, One-shot timer:
to
, Teaching with workpiece:
to
, Upside down display:
, AND: , OR:
, OFF-delay timer:
, One-shot timer:
to
, Teaching without workpiece:
, Light OFF:
, C mode: , I mode:
*. The displays shown in the function transitions are for the default settings.
*. Items shown in the function transitions may increase depending on detailed settings.
*. The items enclosed by dotted red lines are for advanced models only.
(Advanced models with four-color determination do not have
or External input memory .)
Detection Timer
(To increase the response (To use the timer setting)
speed or detection precision)
MODE
Output setting
External input
(To change function controlled (To change the channel 2
by external input.) output)
When the settings
have been completed
➜
Page 20 Refer to 2. Setting the Operation Mode.
Used to increase the response speed or detection precision.
Note: Only I Mode (light intensity determination for red, green, or blue)
can be used with Super-high-speed mode.
Used to set control output timers.
Used to change timer times.
The timer can be set from 1 ms to 5 s.
Used to change the function of the MODE key during
operation.
Used to change the threshold setting level during 1-point teaching.
Example: The threshold level at the default setting (
When the setting is , the threshold level is
1. Used to display the degree of matching and the threshold.
2. Used to display the excess gain (i.e., percentage of matching relative
to threshold) and the threshold.
3. Used to display the peak and bottom degrees of matching at a fixed
interval.
4. Used to display the peak degree of matching when there is a match
and the bottom degree of matching when there is no match.
5. Used to show the detection status with a bar display. Red bars will be
displayed if the degree of match exceeds the threshold.
6. Used to display the present degree of matching and the peak degree
of matching.
7. Used to display the degree of matching and channel number.
Used to change the orientation of the display.
Used to change the item output on control output 2.
Used to set timers for the AND/OR control output.
Used to change timer time.
The timer can be set from 1 ms to 5 s.
Used to change the functions to be remotely controlled with external input.
(For the effective pulse width and other information, refer to the
instructions provided with the product.)
Used to set whether to write the control results to memory.
(Refer to the instructions provided with the product.)
Used to set the judgment mode (detection method). BLACK mode:
The total light intensity for red, green, and blue is used for the judgment.
E3X-DAC-S
External input
Teaching level
MODE key
(To change the function of the
(To change the teaching
MODE key during operation) level)
Display switch
Display orientation
(To reverse the orientation (To change the display
method)
of the display.)
Set the SET/RUN
Mode Selector Switch to
RUN
Description
) is .
.
RUN
.
21