Related Manuals for JDS Uniphase FI Series
Summary of Contents for JDS Uniphase FI Series
- Page 1 FI-SerIeS LIve FIber IdentIFIer Compact live fiber identifier with integrated optical power meter USer ManUaL ZP-PKG-0535 REV 1...
- Page 2 Notice Every effort was made to ensure that the information in this document was accurate at the time of printing. However, information is subject to change without notice, and JDSU reserves the right to provide an addendum to this document with information not available at the time that this document was created.
-
Page 3: Table Of Contents
tabLe OF COntentS Chapter 1 OVERVIEW ..............................4–6 FI-Series Live Fiber Identifier (LFI) ....................4 Features and Components ......................5 Specifications ............................. 6 Chapter 2 OPERATION ............................7–11 Live Fiber Identifier (LFI) ......................... 7 Optical Power Meter (OPM) ......................8 Controls ............................ 8 Display Indicators ........................ -
Page 4: Chapter 1 Overview
overview ChaPter 1 OvervIew FI-SERIES LIVE FIBER The FI-Series Live Fiber Identifier is a compact portable device that integrates live IDENTIFIER (LFI) fiber identification and optical power measurement capabilities into a single tool. This versatile tool can be used to determine live or dark optical signals on a fiber cable without disrupting network traffic. -
Page 5: Features And Components
overview ChaPter 1 FI-Series Live Fiber Identifier Detachable LFI Head Features and Components Cable Alignment Groove LFI Release/Attach Screw 3.7cm x 3.0cm LCD Power Button Inter-Changeable Input for Power Meter OPM Controls Data STORE and RECALL Controls Safe-latch Trigger for Live Fiber Identifier USB Input for Connection to PC... -
Page 6: Specifications
overview ChaPter 1 LFI Specifications 216 x 60 x 38 mm (8.5 x 2.35 x 1.5 inch) dimensions 135 g (4.8 oz) with two AA alkaline batteries weight –20 dbm @ 1310 nm, –30 dbm @ 1550 nm detection sensitivity (typical) 1310 nm: <... -
Page 7: Chapter 2 Operation
operation ChaPter 2 OPeratIOn LIVE FIBER IDENTIFIER Turn power ON. (LFI) Insert fiber into Alignment Groove. Alignment Groove Pull the Safe-latch Trigger down until you hear a clicking sound to ensure Ambient Light Shield is securely engaged. If traffic is present, an audible tone will sound and the device will display “TRAFFIC”... -
Page 8: Optical Power Meter (Opm)
operation ChaPter 2 OPTICAL Note: The LFI head can be removed by turning POWER METER (OPM) the LFI Release/Attach Screw located below the Alignment Groove. LFI Release/Attach Screw dB/dBm - Switches between absolute and relative Power Meter Controls power level display λ - Selects available wavelengths or AUTO wavelength detect ON • Press and hold for 2 seconds to set a reference value ("REF" will flash when set) Power -... -
Page 9: Absolute Power
operation ChaPter 2 Absolute Power The absolute power level (system power measurement) is the amount of optical power present in the system, measured in dBm. The source of this power is the transmitter or transceiver sending information through the system. This test determines whether the signal has enough power to operate the receiver or transceiver at the end of the link. -
Page 10: Relative Power
operation ChaPter 2 Relative Power Acquiring attenuation measurements (optical link loss) on optical components or fiber optic links (e.g., fiber connectors, cable assemblies, installed fiber optic links) is done by measuring the relative power level (dB) at the far end of the link or device under test. Relative power level (attenuation measurement) is the amount of power lost (attenuated) by the optical link being tested, measured in dB. -
Page 11: Replacing Batteries
operation ChaPter 2 Battery Replacement Press the latch on the back cover plate and pull down to remove and obtain access to two AA batteries. Note: The LFI head must be removed to access the battery compartment. FI-SERIES LIVE FIbER IdEntIFIER wIth PowER MEtER... -
Page 12: Chapter 3 Software
Software ChaPter 3 SOFtware Software Installation The following installation process will install FiberChek2, FiberChek2 – QuickView, and a USB Power Meter software application. Insert the software installation disk into your CD drive. System Requirements Follow the setup wizard for FiberChek2: (Minimum) •... -
Page 13: Hardware Recognition
Software ChaPter 3 Hardware Recognition Use the included USB cable to connect to a PC/laptop. The device will be automatically recognized and function as an Optical Power Meter. USB Optical Power As a power meter, this device can be used Meter Software in conjunction with applications that are included on the installation disk (FiberChek2... -
Page 14: Software Controls
Software ChaPter 3 Software Controls Select Measurement Type Users can define the list of wavelengths Import Saved Values Select Wavelength Imports saved values that are stored on the Optical Power Users can define the Meter to a report log (also done by selecting Tools > Import). list of wavelengths Wavelength Setup Use the << and >> arrows to select the wavelengths you want to appear on the OPM by moving them to the box on the right hand side. Power Threshold Sets the level at which the TRAFFIC indicator appears when used as an LFI. Reports Archived logs can be opened by either browsing to the defined path or by selecting: Tools >... - Page 15 Intentionally left blank. FI-SERIES LIVE FIbER IdEntIFIER wIth PowER MEtER...
- Page 16 FAX: 1 301 353 9216 FAX: +1 954 345 4668 FAX: +852 2892 0770 FAX: +49 7181 86 1222 Product specifications and descriptions in this document subject to change without notice. © 2011 JDS Uniphase Corporation. February 2011 ZP-PKG-0535 REV 1...