Danfoss ADAP-KOOL AK-CT 200A User Manual page 34

Menu
Function
Normal operation
Temperature (setpoint)
Thermostat
Differential
Max. limitation of setpoint setting
Min. limitation of setpoint setting
Adjustment of temperature indication
Temperature unit (°C/°F)
Correction of the signal from S4
Correction of the signal from S3 and S3B
Manual service, stop regulation, start regulation (-1, 0, 1)
Displacement of reference during night operation
Define thermostat function
1=ON/OFF, 2=Modulating
Definition and weighting, if applicable, of thermostat sensors -
S4% (100%=S4, 0%=S3)
Time between melt periods
Duration of melt periods
Temperature setting for thermostat band 2 . As differential use
r01
Correction of the signal from S6
Correction of the signal from S6B
Definition and weighting, if applicable, of thermostat sensors
when night cover is on. (100%=S4, 0%=S3)
Heat function
Neutral zone between refrigeration and heat function
Time delay at switch between refrigeration and heat function.
For setting = after 240 min. the heating function is deactivated
Product type: use settings listed in table.
Alarms
Delay for temperature alarm
Delay for door alarm
Delay for temperature alarm after defrost
High alarm limit for thermostat 1
Low alarm limit for thermostat 1
High alarm limit for thermostat 2
Low alarm limit for thermostat 2
High alarm limit for sensor S6 at thermostat 1
Low alarm limit for sensor S6 at thermostat 1
High alarm limit for sensor S6 at thermostat 2
Low alarm limit for sensor S6 at thermostat 2
S6 alarm time delay
With setting = 240 the S6 alarm will be omitted
Alarm time delay or signal on the DI1 input
Alarm time delay or signal on the DI2 input
Signal for alarm thermostat. S4% (100%=S4, 0%=S3)
Delay for S6 (product sensor alarm) after defrost
Delay for temperature alarm S3B
Compressor
Min. ON-time
Min. OFF-time
Time delay for cutin of comp.2
Defrost
Defrost method: 0=none, 1= EL, 2= Gas, 3=Brine, 4=Air
Defrost stop temperature
Interval between defrost starts
Max. defrost duration
34
Parameter
***
r-
***
***
***
A-
c-
d-
User Guide RS8GR602 © Danfoss 2016-10
El-diagram page 12 to 16
Code 1 2 3 4 5 6
- - - 1 1 1 1 1 1
r01 1 1 1 1 1 1
r02 1 1 1 1 1 1
r03 1 1 1 1 1 1
r04 1 1 1 1 1 1
r05 1 1 1 1 1 1
r09 1 1 1 1 1 1
r10 1 1 1 1 1 1
r12 1 1 1 1 1 1
r13 1 1 1 1 1 1
r14 1 1 1 1 1 1
r15 1 1 1 1 1 1
r16 1 1 1 1 1 1
r17 1 1 1 1 1 1
r21 1 1 1 1 1 1
r59 1 1 1 1 1 1
r60 1 1 1 1
r61 1 1 1 1 1 1
r62 1 1 1 1 1 1
r63 1 1 1 1 1 1
r89 1 1 1 1 1 1
A03 1 1 1 1 1 1
A04 1 1 1 1 1 1
A12 1 1 1 1 1 1
A13 1 1 1 1 1 1
A14 1 1 1 1 1 1
A20 1 1 1 1 1 1
A21 1 1 1 1 1 1
A22 1 1 1 1 1 1
A23 1 1 1 1 1 1
A24 1 1 1 1 1 1
A25 1 1 1 1 1 1
A26 1 1 1 1 1 1
A27 1 1 1 1 1 1
A28 1 1 1 1 1 1
A36 1 1 1 1 1 1
A52 1 1 1 1 1 1
A53 1 1 1 1
c01 1 1 1 1 1 1
c02 1 1 1 1 1 1
c05
d01 1 1 1 1 1 1
d02 1 1 1 1 1 1
d03 1 1 1 1 1 1
d04 1 1 1 1 1 1
Min.- Max.-
value value
7 8
1 1 -50°C 50°C 2
1 1 0.1 K 20 K 2
1 1 -49°C 50°C 50
1 1 -50°C 49°C -50
1 1 -10 10 0
1 1 0/°C 1/F 0/°C
1 1 -10 K 10 K 0
1 1 -10 K 10 K 0
1 1 -1 1 0
1 1 -50 K 50 K 0
1 1 1 2 1
1 1 0 % 100 % 100
1 1 0 hrs 10 hrs 1
1 1 0 min. 30 min. 5
1 1 -50°C 50°C 2
1 1 -10 K 10 K 0
-10 K 10 K 0
1 1 0 % 100 % 100
1 1 0 K 50 K 5
1 1 0 min. 240 min. 240
1 1 0 5 0
1 1 0 min. 240 min. 30
1 1 0 min. 240 min. 60
1 1 0 min. 240 min. 90
1 1 -50°C 50°C 8
1 1 -50°C 50°C -30
1 1 -50°C 50°C 8
1 1 -50°C 50°C -30
1 1 -50°C 50°C 8
1 1 -50°C 50°C -30
1 1 -50°C 50°C 8
1 1 -50°C 50°C -30
1 1 0 min. 240 min. 240
1 1 0 min. 240 min. 30
1 1 0 min. 240 min. 30
1 1 0 % 100 % 100
1 1 0 min. 240 min. 90
0 min. 240 min. 90
1 0 min. 30 min. 0
1 0 min. 30 min. 0
1 0 sec 999 sec 5
1 1 0/No 4/Air 1/EL
1 1 0°C 50°C 6
1 1 0 hrs/Off 240 hrs 8
1 1 0 min. 360 min. 45
SW = 1.8x
Factory Actual
setting setting
AK-CT 450A