Danfoss ADAP-KOOL AK-CT 200A User Manual page 28

Fan pause while night blind rolls down
Here you can set the fan pause time, so the night blind can roll down unhindered
to the correct position.
Max. on time for light after manual DI activation
Delay time before light goes off again after light has been turn on manual due to
product stocking.
Service
Temperature measured with S5 sensor
Status on DI1 input. on/1=closed
Read the duration of the ongoing defrost or the duration of the last completed
defrost.
Temperature measured with S3 sensor
Status at the day-/night operation (night operation: on/off )
Temperature measured with S4 sensor
Thermostat temperature
Read the ongoing cutin time for the thermostat or the duration of the last
completed cutin
Read the valve's actual opening degree
Read the temperature at the S6 sensor
Status on DI2 input. on/1=closed
Air temperature. Weighted S3 + S4
Measured temperature for alarm thermostat
* Status on relay for cooling
Status on relay for fan
* Status on relay for defrost
Status on relay for railheat
* Status on relay for alarm
Status on relay for light
* Status on relay for hot gas valve
* Status on relay for compressor 2
* Temperature measured with S5B sensor
* Temperature measured with S3B sensor
* Temperature measured with S6B sensor
* Status on relay for hot gas
* Status on relay for heating element in drip tray
* Status on relay for night blinds
* Status on relay for defrost 2
* Readout of the actual rail heat effect in %
Readout of which thermostat used for regulation: 1= Thermostat 1,
2= Thermostat 2
Status on input DI3 (closed / open)
Readout of the actual cutin value for the thermostat
Readout of the actual cut out value for the thermostat
* Measured temperature for alarm thermostat for B section
* Air temperature. Weighted S3 + S4 temp. for B section
* Status of relay for light 2
* Status of relay for ECO fan
* Status of relay for defrost 3
Status of DI4 input. On=closed
Status of DI5 input. On=closed
Status of DI6 input. On=closed
Status of high-voltage input DI7, 230 V = 1 = closed
Status of high voltage input DI8, 230 V = 1 = closed
0-10 V output indicates EVR valve's degree of opening
28 User Guide RS8GR602 © Danfoss 2016-10
P65 BlindFanStop
P66 Light On Time
Case shutdown
Service
u09 S5 temp.
u10 DI1 status
u11 Defrost time
u12 S3 air temp
u13 Night Cond.
u16 S4 air temp
u17 Ther. air
u18 Ther runtime
u23 Valve OD %
u36 S6 temp
u37 DI2 status
u56 Display air
u57 Alarm air
u58 Comp1/LLSV
u59 Fan relay
u60 Def. relay
u61 Railh. relay
u62 Alarm relay
u63 Light relay
u64 SuctionValve
u67 Comp2 relay
u75 S5 temp. B
u76 S3 air temp B
u79 S6 temp. B
u80 Hotgas valve
u81 Drip tray
u82 Blinds relay
u83 Def. relay 2
u85 Rail DutyC %
u86 Ther. band
u87 DI3 status
u90 Cutin temp.
u91 Cutout temp.
U34 Alarm air B
U35 Display air B
U36 Extra light
U37 Fan Eco
U38 Def. relay 3
U39 DI4 status
U40 DI5 status
U41 DI6 status
U42 DI7 status
U43 DI8 status
U44 AO1 voltage
AK-CT 450A