Dynamix ITM Series Installation, Operation & Maintenance Manual

Integrated tote mixer

Hide thumbs

Table of Contents

Quick Links

Installation, Operation & Maintenance Manual

ITM Series

INTEGRATED TOTE MIXER

Important Safety Instructions

This Installation and Operation Manual Includes

Important Warnings and Safety Information.

Be sure to keep this manual with equipment and

ensure all operators read the enclosed information.

Important Safety Warnings.............................. 2

Receiving, Inspection & Storage ..................... 3

Operation Instructions ..................................... 4

Startup Checklist ............................................. 5

Assembly & Installation

Parts, Maintenance & Service

Terms & Conditions ........................................ 16

Warranty ......................................................... 17

Dynamix Agitators Inc.

150 - 14480 River Road,

Richmond, B.C, Canada V6V 1L4

Ph. 604.244.3771 Fax 604.244.3772

info@dynamixinc.com

www.dynamixinc.com

R16 122016

Plastic Tote ......................................... 6

Stainless Steel Tote ............................ 7

Plastic Tote ......................................... 8

Stainless Steel Tote ............................ 9

ITM SERIES

Integrated Tote Mixer

Table of Contents

Need help?

Do you have a question about the ITM Series and is the answer not in the manual?

Questions and answers

Summary of Contents for Dynamix ITM Series

Page 1: Table Of Contents
Installation, Operation & Maintenance Manual ITM Series INTEGRATED TOTE MIXER Important Safety Instructions This Installation and Operation Manual Includes Important Warnings and Safety Information. Be sure to keep this manual with equipment and ensure all operators read the enclosed information.
Page 2: Important Safety Warnings
Important Safety Warnings Please Read These Warnings Carefully Before Unpacking the Mixer The following safety instructions must be COMPLETELY REVIEWED AND FOLLOWED before operating any Dynamix Mixer. FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN SERIOUS INJURY WARNING! 1. Do not connect to air or electric motor to power source until this Installation operation manual is followed and the mixer is properly assembled and installed as per design 2.
Page 3: Receiving, Inspection & Storage
FOLLOW THESE INSTRUCTIONS COULD RESULT IN SERIOUS INJURY WARNING! Goods must be inspected with 30 days of receive date. It is assumed that goods are satisfactory if Dynamix is not notified within this period. Your mixer has been tested and checked for shaft straightness before shipping. Care must be taken while handling the shaft to ensure proper operation.
Page 4: Operation Instructions
If you have a question about a procedure or are uncertain about any detail, Do Not Proceed. Please contact Dynamix Agitators for more information or clarification. 1. Do not uninstall or service this mixer until you have followed your “Control of Hazardous Energy Sources”...
Page 5: Startup Checklist
Start-up Checklist Please Review This Checklist Carefully Before Operating the Mixer Prior to, and during start-up, please check that the following things have been done:   1. Manual has been read and followed  2. Drive coupling is fully engaged (modular design only) ...
Page 6: Assembly & Installation - Plastic Tote
Assembly & Installation – Plastic Tote ITM Series Assembly Instructions Ensure your shipment came complete with; Drive Segment, Locking Nut, Agitator Segment and Impeller/s as quoted. Note; Impellers are secured via dimple and set screw so that you can reposition your impeller when needed. For applications that require fixed impellers, we recommend permanent or semi-permanent thread lock (Loctite) be used.
Page 7: Stainless Steel Tote
Assembly & Installation – Stainless Steel Tote ITM Series Assembly Instructions Ensure your shipment came complete with; a Drive Segment and Agitator Segment as quoted. Note; Impellers are secured via dimple and set screw so that you can reposition your impeller when needed. For applications which require impellers never move we recommend permanent or semi-permanent thread lock (Loctite) be used.
Page 8: Parts, Maintenance & Service - Plastic Tote
Parts, Maintenance & Service – Plastic Tote Technical Drawing & General Parts List This drawing is not exact. It is only a typical representation of the ITM Series models. When noted, please contact your Dynamix representative with your mixer serial number. REF # PART NAME PART No.
Page 9: Stainless Steel Tote
Parts, Maintenance & Service – Stainless Steel Tote Technical Drawing & General Parts List This drawing is not exact. It is only a typical representation of the ITM Series models. When noted, please contact your Dynamix representative with your mixer serial number. REF # PART NAME PART No.
Page 10 General Information Regarding Electric Motors Overview Be sure to read and understand the Safety Notice statements in this manual. For your protection, do not install, operate or attempt to perform maintenance procedures until you understand the Warning and Caution statements. A Warning statement indicates a possible unsafe condition that can cause harm to personnel.
Page 11 Motor Connections 1. Wiring: Match the motor starter and overload protection to the motor rating. Follow the control manufacturer's instructions. 2. All electrical connections must conform to National Electrical Code and all local regulations. Match line voltage and wire capacity to motor rating found on the motor nameplate. 3.
Page 12 General Information Regarding Air Motors Air motors operate best with lubricated, dry, clean air at air pressures below 100psi. Air Lubricator: Lubricated air is typically available from the air system. If not, an automatic lubricator must be installed in the air- line ahead of the air motor. Use a pneumatic air lubricant e.g. ISO VG32 or detergent SAE #10 automotive oil. Lubricator should be adjusted to feed one drop of oil for every 50 to 75cfm.
Page 13 Air Motor Horsepower Rating & Air Consumption For Air Motors Rated at 1.5HP For Air Motors Rated at 4HP Note: Output rpm refers to motor output shaft only. For gear reduced drives refer to gear ratio on quotation. R16 122016...
Page 14 Note: Air motor rebuilds are often not worth the parts and labor costs considering with the resulting performance vs. purchasing a new air motor. Please email or call to request current procedure from Dynamix Agitators Inc. info@dynamixinc.com - (604) 244 3771 Air Motor 1.5HP Rating...
Page 15 Air Motors; 3HP Rating Please email or call to request current procedure from Dynamix Agitators Inc. info@dynamixinc.com - (604) 244 3771 Exploded views are shown for reference only. Units may vary depending upon specific model. Please refer to factory if you are unsure of your model.
Page 16 Gear Driven Gear Driven mixers are lubricated at the factory using the proper type and amount of lubricant for normal service. For additional information contact Dynamix Agitators. Air Motor Air Motor lubricator should be adjusted to feed one drop of oil every 50-75 CFM.
Page 17 Troubleshooting Guide Use This Chart to Diagnose Operation Issues Problem Possible Cause Possible Solution   Loose connections Check and tighten connection   Incorrect wiring Check wiring diagram and wire correctly   Mixer Will Blown fuse Replace fuse ...
Page 18: Terms & Conditions
Products for modification, repair or replacement must be authorized by Dynamix in writing prior to return of the Products by the Customer. Dynamix will not be responsible for any repairs performed by third parties unless the extent, or terms and costs of such repairs, are authorized by Dynamix, in writing in advance.
Page 19: Warranty
Agreement. If any part of these Delivered Terms are found invalid, the remaining part will be effective. No waiver, alteration or modification of any of the provisions of these Delivered Terms will be binding on Dynamix, unless made in writing and signed by a duly authorized officer of Dynamix. These Delivered Terms, the Quotation and its attached terms and conditions, and any other terms referenced in the Quotation contain the entire agreement of the parties.
Page 20 Product in respect of which damages are unclaimed. 3. What Is Not Covered By Warranty: Damages and Claims for Which Dynamix Is Not Responsible The following are examples of the kinds of defect which are not covered by Our warranty; defects which are caused by improper installation, improper or abnormal use or operation, or improper storage or handling;...
Page 21 Details of claim Dynamix will notify the customer whether it will be necessary to return the Product or part or component to us. If so, we will send the customer an "AUTHORIZED RETURN NUMBER" that must be attached to the product or part or component before returning it.
Page 22 R16 122016...
Page 23 Warranty Data Sheet To validate your warranty, please complete this form and return to: Dynamix Agitators Inc. #150-14480 River Road Richmond, BC, Canada V6V 1L4 Mixer Model Number Serial Number Purchase Order Number Date Received Tank Number or Location Agitator Start Up Data...