Denon AVR-X6200W Service Manual page 93

Error
DPMS Update Error Display
Code
S u b
5B
U p d a t i n g
S u b
5C
U p d a t i n g
S u b
5D
U p d a t i n g
S u b
5E
U p d a t i n g
S u b
5F
U p d a t i n g
S u b
60
U p d a t i n g
S u b
61
U p d a t e C h e c k N G
S u b
62
U p d a t i n g
G U I
80
U p d a t i n g
G U I
81
U p d a t i n g
G U I
82
U p d a t i n g
G U I
83
U p d a t i n g
G U I
84
U p d a t i n g
G U I
85
U p d a t i n g
G U I
86
U p d a t i n g
E t h e r I M G
A0
C o n n e c t i o n F a i l A 0
NACK received in response or
* * * m i n
no response from Sub for the "L"
f a i l 5 B
command.
* * * m i n
No Update Packet received from
CY920 (Time Out).
f a i l 5 C
* * * m i n
Abnormal data in Update Packet
received from CY920 (CRCError).
f a i l 5 D
Abnormal data in Update Packet
* * * m i n
received from CY920 (PacketNo-
f a i l 5 E
Error).
* * * m i n
Setup failure of the XModem
transfer method.
f a i l 5 F
NACK received in response or
* * * m i n
no response from Sub for the "P"
f a i l 6 0
command.
Mismatched Check Sum in re-
* * * m i n
sponse or no response from Sub
6 1
for the "I" command.
* * * m i n
Failed to start up Sub in Power On
sequence during Update.
f a i l 6 2
Write Enable Latch Bit not set in
* * * m i n
Read after issuing the "WREN"
f a i l 8 0
command.
* * * m i n
Block Erase failed in Read after
issuing the "BE" command.
f a i l 8 1
* * * m i n
No Update Packet received from
CY920 (Time Out).
f a i l 8 2
* * * m i n
Abnormal data in Update Packet
received from CY920 (CRCError).
f a i l 8 3
Abnormal data in Update Packet
* * * m i n
received from CY920 (PacketNo-
f a i l 8 4
Error).
* * * m i n
Setup failure of the XModem
transfer method.
f a i l 8 5
* * * m i n
Mismatched Check Sum in Check
Sum comparison after rewriting.
f a i l 8 6
* * * m i n
IP Address acquisition failure
(AutoIP).
93
Details of Error code Remedies
Turn off and on the power. Updating
starts automatically.
Turn off and on the power. Updating
starts automatically.
Turn off and on the power. Updating
starts automatically.
Turn off and on the power. Updating
starts automatically.
Turn off and on the power. Updating
starts automatically.
Turn off and on the power. Updating
starts automatically.
Turn off and on the power. Updating
starts automatically.
Turn off and on the power. Updating
starts automatically.
Turn off and on the power. Updating
starts automatically.
Turn off and on the power. Updating
starts automatically.
Turn off and on the power. Updating
starts automatically.
Turn off and on the power. Updating
starts automatically.
Turn off and on the power. Updating
starts automatically.
Turn off and on the power. Updating
starts automatically.
Turn off and on the power. Updating
starts automatically.
Check the network connection. Carry
out the update in an environment that
has little network load.