Technical Specifications - Denon AVR-X6200W Service Manual

TECHNICAL SPECIFICATIONS

n Audio section
• Power amplifier
Rated output :
Front：
140W+140W (8Ω, 20Hz - 20kHz with 0.05% T.H.D.)
175W+175W (6Ω, 1kHz with 0.7% T.H.D)
Center :
140W (8Ω, 20Hz - 20kHz with 0.05% T.H.D.)
175W (6Ω, 1 kHz with 0.7 % T.H.D.)
Surround :
140W+140W (8Ω, 20 Hz - 20 kHz with 0.05% T.H.D.)
175W+175W (6Ω, 1 kHz with 0.7 % T.H.D.)
Surround back / Height1 / Front wide / Height2:
140W+140W (8Ω, 20 Hz - 20 kHz with 0.05% T.H.D.)
175W+175W (6Ω, 1 kHz with 0.7 % T.H.D.)
Rated output :
160 W x 2-channel (8 Ω)
250 W x 2-channel (4 Ω)
Output connectors : 4 - 16 Ω
n Analog section
Input sensitivity/Input impedance : 200 mV / 47 kΩ
Frequency response : 10 Hz - 100 kHz — +1, -3 dB(Direct mode)
S/N : 102 dB(IHF-A weighted, Direct mode)
Distortion : 0.005 % (20 Hz – 20 kHz) (Direct mode)
Rated output : 1.2 V
n Digital section
D/A output : Rated output — 2 V (at 0 dB playback)
Total harmonic distortion — 0.008 % (1 kHz, at 0 dB)
S/N ratio — 102 dB
Dynamic range — 100 dB
Digital input : Format — Digital audio interface
n Phono equalizer section
Input sensitivity : 2.5 mV
RIAA deviation :
±1 dB (20 Hz to 20 kHz)
S/N : 74 dB (IHF-A)
Distortion factor : 0.03 % (1 kHz, 3 V)
n Video section
• Standard video connectors
Input/output level and impedance : 1 Vp-p, 75 Ω
Frequency response : 5 Hz - 10 MHz — 0, -3 dB
• Color component video connector
Input/output level and impedance : Y signal — 1 Vp-p, 75 Ω
Frequency response : 5 Hz - 60 MHz — 0, -3 dB
PB / CB signal — 0.7 Vp-p, 75 Ω
PR / CR signal — 0.7 Vp-p, 75 Ω
n Tuner section
Reception frequency range :
Effective sensitivity : FM 1.5μV(14.8dBf)
AM 20 μV
50 dB sensitivity : MONO ― 2.8 μV (20.2 dBf)
S/N ratio (IHF-A) : MONO ― 78 dB
STEREO ― 68 dB
HD ― FM 85dB AM 85dB
Distortion (1 kHz) : MONO ― 0.1 %
SRETEO ― 0.2 %
HD ― FM 0.02% AM 0.02%
n Wireless LAN section
Network type
(wireless LAN standard) : onforming to Wi-Fi®z1
Security : WEP 64 bit, WEP 128 bit
WPA/WPA2-PSK (AES)
WPA/WPA2-PSK (TKIP)
Radio frequency : 2.4 GHz
No. of channels : 1 - 11 ch (for E3)
1 - 13 ch (for E2, E1C)
z1 The Wi-Fi® CERTIFIED Logo and the Wi-Fi CERTIFIED On-Product
Logo are registered trademarks of the Wi-Fi Alliance.
n Bluetooth section
Communications system : Bluetooth Version 2.1 + EDR
(Enhanced Data Rate)
Transmission power : Maximum 2.5 mW (Class 2)
Maximum communication range : Approx. 32.8 ft/10 m in line of sight
Frequency band : 2.4 GHz band
Modulation scheme : FHSS (Frequency-Hopping Spread Spectrum)
Supported profiles :
A2DP 1.2 (Advanced Audio Distribution Profile)
AVRCP 1.4 (Audio Video Remote Control Profile)
Corresponding codec : SBC, AAC
Transmission range (A2DP) : 20 Hz - 20,000 Hz
n General
Power supply : (for E3) :
(for E2) :
(for E1C) :
Power consumption : 730W
Power consumption in standby mode : 0.1 W
Power consumption in CEC standby mode : 0.5 W
Power consumption in network standby mode : 4.5W
For purposes of improvement, specifications and design are subject to
change without notice.
9
FM 87.5 MHz - 107.9 MHz(for E3)
FM 87.5 MHz - 108.0 MHz(for E2, E1C)
AM 530 kHz - 1710 kHz(for E3)
AM 522 kHz - 1611 kHz(for E2, E1C)
AC 120 V, 60 Hz
AC 230 V, 50 Hz / 60 Hz
AC 220 V, 50 Hz