Denon AVR-X6200W Service Manual page 26

2-1 D IAGNOSTIC MODE (Service Path Check Mode)
2-1.1. Actions
This function is convenient for confirming problem paths in the product and executing a path check after repair.
The Video and Audio paths can be checked.
The backup data is not rewritten.
2-1.2. Starting up
Hold down buttons "STATUS" and "ZONE3 SOURCE" at the same time and press the power button to turn on the power.
Select "1. SERVICE CHECK" and press the "ENTER" button to start the diagnostic mode.
The "TUNED", "STERO" and "RDS" segments are lit in this mode.
2-1.3. Canceling diagnostic mode
Press the power button to turn off the power.
2-1.4. Selecting items
Press q button to switch between video items and audio items.
Press button w or e to select the previous or next item.
The unit
q w
Actions
Audio ⇔ Video PREVIOUS
Button DIMMER CURSOR 0
2-1.5. Audio system confirmation items
fig. XX: See the block diagram of the fig.XXth.
Paths confirmation item
Analog
A 0 1 : A N A L O G
(MAIN ZONE) fig.01
1
Digital
A 0 2 : D I G I T A L
(MAIN)
fig.02a
fig.02b
2
Digital (signal) Path
A 0 3 : D I G I T A L - Z 2
fig.03a
(ZONE2)
fig.03b
fig.03c
3
Remote control unit
e q w
NEXT Audio ⇔ Video PREVIOUS
CURSOR 1 SLEEP CURSOR 0
Display
Input Source : CBL/SAT
P A S S
Input Mode : Analog (fixed)
Amp assign : 9.1ch
Floor Layout : 5.1 & Surround Back
Height Sp : 2ch
Dolby Sp : None
Height Layout : Front Height
MAIN ZONE : ON
ZONE2 : OFF
ZONE3 : OFF
Input Source : CBL/SAT
Input Mode : Digital (fixed)
Sound mode : Multi Ch Stereo
Vol. : 60.0 (-20.0dB)
Amp assign : 9.1ch
Floor Layout : 5.1 & Surround Back
Height Sp : 2ch
Dolby Sp : None
Height Layout : Front Height
Speaker Select : Floor
Speaker Config : All Speaker = Small/Subwoofer = 2spkrs
MAIN ZONE : ON
ZONE2 : OFF
ZONE3 : OFF
Input Source : Online Music
Input Mode : Auto
Sound mode : Stereo
Amp assign : 7.1ch + ZONE2
Speaker for ZONE2 : Surround Back
Floor Layout : 5ch
Height Sp : 2ch
Dolby Sp : None
Height Layout : Front Height
MAIN ZONE : ON
ZONE2 : ON
ZONE3 : OFF
e
NEXT
CURSOR 1
Settings
・Analog input ⇒ Speaker output (Front L/R)
・Analog input ⇒ Preout output (Front L/R)
(bAs the input source, you can switch from CBL/SAT to other ones.)
・Digital input ⇒ Speaker output (Front L/R, Center, Surround L/R, Surround Back L/R)
・Digital input ⇒ Preout output (Front L/R, Center, Subwoofer1/2, Surround L/R, Surround Back L/R)
(bAs the input source, you can switch from CBL/SAT to other ones.)
・Digital (PCM) input ⇒ Speaker output (Surround Back L/R → ZONE2 L/R)
・Digital (PCM) input ⇒ Preout output (ZONE2 L/R)
(bAs the input source, you can switch from Online Music to other ones.)
26
Contents of confirmation Remarks