Scion Instruments 436-GC Service Manual page 66

436-GC/456-GC
Code Error Description
142 Aux 3 EFC Hardware Error
143 Aux 4 EFC Hardware Error
144 Aux 5 EFC Hardware Error
145 Aux 6 EFC Hardware Error
146 Aux 7 EFC Hardware Error
147 Aux 8 EFC Hardware Error
TCD no Air Leak (position)
230 Front TCD no Air leak
231 Middle TCD no Air leak
232 Rear TCD no Air leak
TCD Air Leak fault (position)
233 Front TCD Air leak fault
234 Middle TCD Air leak fault
235 Rear TCD Air leak fault
Max Setup Temper Exceeded (position)
247 Column Oven Max Setup Temper Exceeded
248 Zone 1 Max Setup temper Exceeded
249 Zone 2 Max Setup temper Exceeded
250 Zone 3 Max Setup temper Exceeded
251 Zone 4 Max Setup temper Exceeded
252 Zone 5 Max Setup temper Exceeded
253 Zone 6 Max Setup temper Exceeded
Temperature Zone
260 Column Temperature Out Of Tolerance
261 Zone 1 Temperature Out Of Tolerance
262 Zone 2 Temperature Out Of Tolerance
263 Zone 3 Temperature Out Of Tolerance
264 Zone 4 Temperature Out Of Tolerance
265 Zone 5 Temperature Out Of Tolerance
266 Zone 6 Temperature Out Of Tolerance
Detector EFC Flow out of range
304 Front DFC Chan1 out of range
305 Front DFC Chan2 out of range
If the used gas is Hydrogen (H ) the Error level is Error, in all other cases an Alert is given.
2
2
SCION Instruments
Error level
Event
Event
Event
Alert
Alert
Alert
Error
Error
Error
Error
Error
Error
Error
Alert Error 2
Alert/ Error
436-GC/456-GC Service Manual Revision B February 2019
Cause Condition(s)
When error (18) is solved within 4 minutes after error
(18) appears
When error (18) is solved within 4 minutes after error
(18) appears
When error (18) is solved within 4 minutes after error
(18) appears
4 minutes after error (18) where there has been no
"No Air Leak"
4 minutes after error (18) where there has been no
"No Air Leak"
4 minutes after error (18) where there has been no
"No Air Leak"
Defect Sensor. Temperature is
10 °C above set temperature limit
Defect Sensor. Temperature is
10 °C above set temperature limit
Defect Sensor. Temperature is
10 °C above set temperature limit
Defect Sensor. Temperature is
10 °C above set temperature limit
Defect Sensor. Temperature is
10 °C above set temperature limit
Defect Sensor. Temperature is
10 °C above set temperature limit
Defect Sensor. Temperature is
10 °C above set temperature limit
Flow is above max +10 % or below -5 mL/min for
more then 10 sec.
Flow is above max +10 % or below -5 mL/min for
Page: 65
GC action Action needed
Notification Message -
Notification Message -
Notification Message -
Turn Electronics and power Find source and repair/replace
off hardware
Turn Electronics and power Find source and repair/replace
off hardware
Turn Electronics and power Find source and repair/replace
off hardware
Electronics off (all)
Check Column Oven zone
H2 flow set to 0.0 mL/min
Electronics off (all)
Check zone (1)
H2 flow set to 0.0 mL/min
Electronics off (all)
Check zone (2)
H2 flow set to 0.0 mL/min
Electronics off (all)
Check zone (3)
H2 flow set to 0.0 mL/min
Electronics off (all)
Check zone (4)
H2 flow set to 0.0 mL/min
Electronics off (all)
Check zone (5)
H2 flow set to 0.0 mL/min
Electronics off (all)
Check zone (6)
H2 flow set to 0.0 mL/min
Turn off/on flow, check source
Activate Safety Method
(gas-supply)
Activate Safety Method Turn off/on flow, check source
510 Error codes