Table of Contents
Advertisement
Item Item value
20
Gain
21
Offset
22
Burn in
23
EEPROM Init
24
Bcak LIT Time
25
Total Time
26
BackLight
27
Language
28
System Reset
29
Exit
How to Exit the Factory mode
Use one of the following methods:
•
Select EXIT_FACTORY from the menu and press the "OK"
button.
Note: When the TV is switched "off" by a power interrupt, or
normal switch to "stand-by" while in the factory mode, the TV
will show up in "normal operation mode" as soon as the power
is supplied again. The error buffer will not be cleared.
5.2.3
Customer Service Mode (CSM)
Purpose
The Customer Service Mode shows error codes and
information on the TV's operation settings.The call centre can
instruct the customer (by telephone) to enter CSM in order to
identify the status of the set.This helps the call centre to
diagnose problems and failures in the TV set before making a
service call.
The CSM is a read-only mode; therefore, modifications are not
possible in this mode.
Specifications
•
Ignore "Service unfriendly modes".
•
Line number for every
line (to make CSM language independent).
•
Set the screen mode to full
screen (all contents on screen is visible).
•
After leaving the Customer Service Mode, the original
settings are restored.
•
Possibility to use "CH+" or "CH-" for channel surfing, or
enter the specific channel number on the RC.
How to Activate CSM
To activate CSM, press the following key sequence on a
standard remote control transmitter: "456987" (do not allow the
display to time out between entries while keying the sequence).
After entering the Customer Service Mode, the following items
are displayed.
Note: Activation of the CSM is only possible if there is no (user)
menu on the screen!
Contents of CSM
•
1.1 Set Type This information is very helpful for a
helpdesk/workshop as reference for further diagnosis. In
this way, it is not necessary for the customer to look at the
rear of the TV-set. Note that if an NVM is replaced or is
initialized after corruption, this set type has to be re-written
to NVM.
•
1.2 Production code Displays the production
code (the serial number) of the TV. Note that if an NVM is
replaced or is initialized after corruption, this production
code has to be re-written to NVM.
•
1.3 HDCP keys Indicates the validity of the HDMI keys (or
HDCP keys). In case these keys are not valid and the
Service Modes and Fault Finding
Default value
32"
39"
42"
Description
RGB
RGB
RGB
ADC Gain
RGB
RGB
RGB
Offset RGB
OFF
Turn on or turn off Burn in pattern
Initial all EEPROM except the HDCP key and product serial number
00003.4
00000.
00000.
Bcaklight time
Hrs Hrs
0Hrs
6Hrs
Hrs
Hrs
00004.6
00000.
00000.
Total time
Hrs Hrs
0Hrs
6Hrs
Hrs
Hrs
100
Set the brightness of the backlight
English
Factory Lanuguage
Reset the EEPROM data except the HDCP,product serial number,the factory menu ADC data,white balance set
point,Black light,language and Energy Logo.
Exit
customer wants to make use of the HDMI functionality, the
SSB has to be replaced.
•
1.4 NVM name Detects and displays NVM name.
•
1.5 Software Version Displays the software version.
•
1.6 SSB Gives an identification of the SSB as stored in
NVM. Note that if an NVM is replaced or is initialized after
corruption, this identification number has to be re-written to
NVM. This identification number is the 12NC number of the
SSB.
•
1.7 LCD display panel 12NC NVM read/write.
•
1.8 PSU 12NC NVM read/write.
•
1.9 RS232 Display RS232.
•
2.0 TV Region Display TV region.
How to Exit CSM
To exit CSM, use one of the following methods.
•
Press the MENU/HOME button on the remote control
transmitter.
•
Press the POWER button on the remote control
transmitter.
•
Press the POWER button on the television set.
back to
div. table
TPS10.1A LA
5.
EN 15
2013-Sep-06
Hide quick links:
Advertisement
Table of Contents
