Table of Contents
Advertisement
EN 22
7.
TPS10.1A LA
7.2
Power Supply
Refer to figure
Figure 7-3
platform.
Display Interfacing
CN8901 for 715G5654
CN8101 for 715G5670
Display power
PFC
7.2.1
Power Supply Unit
All power supplies are a block box for Service. When defective,
a new board must be ordered and defective one must be
returned,unless the main fuse of the board is broken. Always
replace a defective fuse with one with the correct
specifications! This part is available in the regular market.
Consult the Philips Service web portal for the order codes of the
boards.
Important delta's with the AP 3000 series platform are:
•
New power architecture for LED backlight
•
"Boost" signal is now a PWM-signal + continuous variable.
The control signals are:
•
Stand-by
•
Lamp "on/off"
•
DIM (PWM) (not for PSDL)
In this manual, no detailed information is available because of
design protection issues.
The output voltages to the chassis are:
•
+3V3-STANDBY (Stand-by mode only)
•
+12V (on-mode)
•
+Vsnd (+24V) (audio power) (on-mode)
•
+24V (bolt-on power) (on-mode)
•
Output to the display; in case of
- IPB: High voltage to the LCD panel
- PSL and PSLS (LED-driver outputs)
- PSDL (high frequent) AC-current.
7.2.2
Diversity
The diversity in power supply units is mainly determined by the
diversity in displays.
2013-Sep-06
Circuit Descriptions
for the power architecture of this
Ac-input + Mains filter
Figure 7-3 Power Architecture
Platform power
BL-ON/OFF
DIM
12V
24V
5V
Low stby
power
AC IN
CN9901
The following displays can be distinguished:
•
CCFL/EEFL backlight: power board is conventional IPB
•
LED backlight:
- side-view LED without scanning: PSL power board
- side-view LED with scanning: PSLS power board
- direct-view LED without 2D-dimming: PSL power board
- direct-view LED with 2D-dimming: PSDL power board.
PSL stands for Power Supply with integrated LED-drivers.
PSLS stands for a Power Supply with integrated LED-drivers
with added Scanning functionality (added microcontroller).
PSDL stands for a Power Supply for Direct-view LED backlight
with 2D-dimming.
7.2.3
Connector overview
Table 7-1 Connector overview
no.
Descr.
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
back to
div. table
LVDS
AMP
AMP
24V
Platform
MST6931
CN701
1 power- PCB
Connector
32PFL3008/98/39PFL3008/98
42PFL3008/98
CN8901
CN9902
CN8101
to panel
to SSB
to panel
CN8901
CN9902
CN8101
LED-source
n.c.
VLED+
n.c.
+5.2V
n.c.
LED-1
+5.2V
LED1
n.c.
PS_ON
LED2
n.c.
+24V
n.c.
n.c.
+24V
n.c.
n.c.
GND
n.c.
n.c.
GND
n.c.
n.c.
GND
LED4
LED-1
+12V
LED3
n.c.
+12V
n.c.
LED-source
DIM
VLED+
-
ON/OFF
-
12V
19450_202_130128.eps
130128
CN9102
to SSB
CN9102
n.c.
+5V
+5V
PS_ON
+24V
+24V
GND
GND
GND
+12V
+12V
PDIM
ON/OFF
Hide quick links:
Advertisement
Table of Contents
