Panasonic Panafax UF-885 Service Manual page 162

Panasonic UF-885 / 895
1. Printer Error Code Table
Error
Code
00 No problem detected
10 The Timing Sensor turned OFF before a certain period of
time.
11 Timing Sensor did not turn ON within a certain period of time.
(Original Cassette Feeder)
12 Timing Sensor did not turn On within a certain period of time.
(250 sheet Optional Cassette Feeder)
13 Timing Sensor did not turn On within a certain period of time.
(500 sheet Optional Cassette Feeder)
14 Timing Sensor did not turn OFF within a certain period of time. 1. Recording Paper Jam.
15 Paper Eject Sensor did not turn ON within a certain period of
time.
16 Paper Eject Sensor did not turn OFF within a certain period of
time.
17 Timing Sensor detected paper while initializing the unit.
18 Paper Cassette was removed while Recording Paper was
Feeding.
1B Paper Cassette was removed while Recording Paper was
Feeding.
22 The temperature of the Fuser Roller remained low even after
the circuit was activated.
23 Abnormally high Fuser Roller temperature after the circuit was
de-activated.
24 The temperature of the Fuser Roller was not controlled within
a certain margin.
25 Thermistor open.
26 Thermostat detected temperature over 200°C.
31 The Polygon Motor did not reach a constant speed of 10000
rpm within a certain period of time.
32 The Polygon Motor did not maintain a constant speed of
10000 rpm.
36 HSYNC signal abnormal.
41 Fan does not rotate.
54 A/D Converter error.
55 Printer Motor Ready Signal abnormal.
61 Unit detected "No Toner Cartridge".
63 Unit detected "Printer Door Open".
64 Unit detected "No Cassette".
65 Unit detected "Out of Paper".
68 Jam Access Cover of Optional 250 Sheet Feeder is open.
69 Jam Access Cover of Optional 500 Sheet Feeder is open.
71 Interface error occurs with the 500 sheet optional cassette.
162
Description of Problems Cause
1. Recording Paper Jam.
2. Timing Sensor defective
3. Incorrect paper size setting.
1. Recording Paper misfeeding, Paper Feed Roller defective.
2. Drive Clutch defective.
3. Timing Sensor defective.
1. Recording Paper misfeeding, Paper Feed Roller defective.
2. Drive Clutch defective.
3. Timing Sensor defective.
1. Recording Paper misfeeding, Paper Feed Roller defective.
2. Drive Clutch defective.
3. Timing Sensor defective.
2. Timing Sensor defective
3. Incorrect paper size setting.
1. Recording Paper Jam.
2. Paper Eject Sensor defective.
1. Recording Paper Jam.
2. Paper Eject Sensor defective.
1. Recording Paper jammed in the unit.
2. Timing Sensor defective.
1. Recording Paper jammed in the unit.
2. Paper Eject Sensor defective.
1. Recording Paper Jam.
1. Fuser Unit defective.
2. LPC PCB defective.
3. LVPS defective.
1. Fuser Unit defective.
2. LPC PCB defective.
3. LVPS defective.
1. Fuser Unit defective.
2. LPC PCB defective.
3. LVPS defective.
1. Thermistor defective (Fuser Unit).
2. LPC PCB defective.
1. Thermostat defective (Fuser Unit).
2. LPC PCB defective.
3. LVPS defective.
1. LSU defective.
1. LSU defective.
1. LSU defective.
2. LPC PCB defective.
1. Fan defective.
2. LPC PCB defective.
1. LPC PCB defective.
1. Connector is not properly connected.
2. Printer Motor defective.
3. LPC PCB defective.
1. Toner Cartridge not installed.
2. Toner Sensor defective.
1. Printer door is not closed.
2. ILS PCB defective.
1. Cassette not installed or partially open.
2. Cassette Sensor defective.
1. Cassette(s) ran out of receiving paper.
2. Paper Detect Sensor defective.
1. Jam Access Cover Sensor of Optional 250 Sheet Feeder
defective.
1. Jam Access Cover Sensor of Optional 500 Sheet Feeder
defective.
1. CN101 is disconnected.
2. CST3 PCB defective.