FeiYu Tech G4 Quick Start Manual

G4 Handheld Gimbal For Smartphone
Suitable for iPhone6 / 5C / 5S / 5 / 4S / 4 and similar ones.
1
Beginner Guide
Attention ! Please install the suitable smartphone first before power on the Gimbal.
Insert The Batteries Install The Phone
Remove the power Install the Smart phone
switch cap, insert two by the quick-release
batteries into the handle. adapter. And make
sure it is fixed well.
Power On
Confirm the phone is
installed well, then press
the power button to turn
on the Gimbal.
2
Product Appearance Instructions
Pitch Axis
Heading Axis
Function Button
Power Switch
If any comments or suggestions please do not hesitate
to e-mail us directly : service@feiyu-tech.com
In order to get the best working status ,
please try to keep the smart phone and
R
pitch axis balance before power on the
gimbal. Please refer to thefollowing:
iPhone5
5 mm
Standard Installation Method
Mode Switching
When the Gimbal is working, you can
press the function button to switch
among the working modes and a special
working condition freely.
( Details of working modes please refer to the
instructions of working modes )
Indicator
Roll Axis
Indicator Explanation
LED Status
Blue light flashes
three times
Blue light flashes
Function Interface
twice
Blue light flashes
once
Blue light keeps
flashing
The indicator flashes in red light
when in working, it will prompt the
Gimbal at fault.
3
Working Mode Instructions
EN
Function Button
FEIYU-EN-1
Identify the working mode via
switch to different status of the
indicator light.
Use for switching working modes.
Special Working Condition (Inversion Mode)
the Gimbal enter into the inversion mode and switch to the Heading following mode automatically. Invert the Gimbal to capture more
excited scenes easily by switching mode combination. When in inversion working condition press the function button for three times in
succession to reset the Gimbal back to the original state.
Press function button for 3 seconds, the motor stop working and the LED of the function button will single flashes this
Standby Mode
will indicate that gimbal enter the standby mode. Single press the function button the gimbal will be awaken immediately.
Hand Pulling Locking The pitching can be adjust by hand pulling after start the gimbal 8 seconds. During the Heading Follow Mode
pulling the pitching to the desired angle and stay 0.5 second it will lock in the current angle.
iPhone6
Item LED Status
Single Press Single Flashes
Double Press Double Flashes
0 mm
Three Press Single Flashes
4
Filming Skill
Smooth And Steady Filming: Handheld the Gimbal, keep stable for movement, keep light and steady for walking.
Adjust The Pitching Angle:
Manual Adjust: Switch to heading follow mode or inversion mode,control the pitch angle to the the position you want, and
keep for 0.5 second,the gimbal will lock current angle.
Auto Adjust: Double press the function button to enter into"Heading And Pitch Follow Mode". Hold the Gimbal at the
desired angle, then press the button once to reengage "Heading Follow Mode" in order to lock the angle of desired pitch.
Remote Control To Adjust:
Flexible Use Of Inversion Mode: Press the function button for three times in succession, the Gimbal switch to the
inversion mode and help to captured low angle view more easily. If filming with moving forward at a high speed, keep the
handle roughly parallel with the ground will be helpful.
5
Function Interface Instructions
! Please Remove
The Batteries
Before Upgrading
Connection Mode
Explain
Firmware Upgrade Instruction
Full Power
Please visit the official website of Feiyu Tech: www.feiyu-tech.com to download the USB driver, firmware upgrade software and the latest
firmware then unzip the RAR file.Remove the batteries and refer to the connection diagram to connect the gimbal with the computer.
Please refer to the manual of update operation to upgrading,otherwise the Gimbal will be abnormal.
Enough Power
Attention : Please be sure to connect the computer with the USB connector.
Parameters Configuration
Low Power The heading following speed can be configurate through parameter setting software.User can adjust to the desired following speed mode
according to the requirements of filming scene. Three modes for optional: "SLOW" mode, "NORMAL" mode , "FAST" mode.
Default setting is "FAST" mode.
Attention : Please be sure to connect the computer with the USB connector.
No Power
Gimbal Calibration
The Gimbal attitude can be calibrate through parameter setting software. User can adjust the pitch and roll in a small angle to achieve more
accuracy filming scene. Please insert the batteries then refer to the connection diagram to connect the gimbal with the computer for caliration.
Attention : Please be sure to connect the computer with the USB connector.
Working Mode Instructions
Heading Follow Mode：Camera Pitch and Roll Angles
1.
remain constant, heading follows the handheld position.
2. Heading And Pitch Follow Mode：Camera Roll Angle remains
constant. Heading and Pitch follow the handheld position.
When in any working mode, press the function button for three times in succession,
Function Explanation Item
Heading Follow Mode Long Press For 1 Second
Heading And Pitch Follow Mode Long Press For 3 Second
Inversion Mode
Customer can adjust the gimbal like mode switch or pitch angle by connecting remote control.
Function
USB Cable
Interface
Attention: Be sure to connect the computer with the USB connector
The USB Mini terminal of the cable plug into the function interface , the USB terminal plug
into the USB connector. Please ensure to connect with the USB connector.
LED Status Explanation
Single Flashes Pitch Recover Level
Single Flashes Standby Mode
Upgrade........
USB Connector
PC