FeiYu Tech G4S Beginner's Manual

G4S 3-Axis Handheld Gimbal
Suitable for GoPro HERO 4 / HERO 3+ / HERO 3
1
Beginner Guide
( 1 ) Please install the suitable camera first before power on the Gimbal.
Attention !
!
( 2 ) Please turn off the power when not in use.
1
Insert The Batteries Mount the Camera
Remove the power switch Mount the camera carefully to
cap, insert two 18350 the mounting bracket and make
batteries into the handle. sure the camera is firmly connected
with the MINI-USB 10Pin.
4
Power On / Off
Power On: Single tap the function button,the
gimbal shall be powered on after 2 seconds.
Power Off: Hold down the function button for
3 seconds to turn off the gimbal.
Attention: Turn the gimbal on
after ensuring the camera is secure.
2
Product Appearance Instructions
360°
Panning
360° 360°
Function
Interface
Tilting
360°
Rolling
If any comments or suggestions please do not hesitate
to e-mail us directly : service@feiyu-tech.com
Applicable to the firmware V1.25 and above version
2
MINI-USB
10Pin
Assembly the clip
Press the clip at both ends of the
clip, clip it as above picture.
Rolling
Tilting
Indicator
Panning
Joystick
Indicator Explanation
Function Button
（ ON / OFF ）
LED Status
Blue light flashes
three times
Blue light flashes
twice
Blue light flashes
once
1/4 Inch Screw Hole
Blue light keeps
flashing
If the indicator light flashes red, the
Gimbal will not work correctly due to
an error.
3
Operation Instructions
EN
LED Status
Indicator
Version 2.0
Single flash
Light
Status
Double flashes
Three flashes
Always on
Flash quickly
3
Working Mode Instructions
Panning Mode
Camera is permitted to pan left or right. Vertical tilts or rolls are restricted.
Panning and Tilting Mode
Lock Mode
Camera stays in its current orientation. All panning, tilting and rolls are restricted.
Other Function
Inversion Mode
When in any working mode, press the function button
for three times in succession, the Gimbal will enter into the inversion mode
and switch to the Panning Mode automatically.
Invert the Gimbal to capture more excited scenes easily by switching mode
combination. When in inversion working condition press the function button
Joystick
for three times in succession to reset the Gimbal back to the original state.
You can control
Operating Instructions of Function Button
the direction by
the joystick
Operation
Single tap
Double tap
Triple tap
Quadruple tap
Tap button for six times
Long press for 1 second
Long press for 3 seconds
4
Video Output
Function
Interface
5
Read the GoPro SD card and Charge the GoPro
Explain
Full Power
Enough Power
Low Power
No Power
G4S 3-Axis handheld gimbal has a mini to micro port, It can connect the GoPro with a micro usb cable. You can read the GoPro SD card and
Charge the GoPro without dismount the GoPro, and it works when the gimbal is powered off.
The GoPro charging switch and the SD card reading switch works independently, and it works when the gimbal is powered off. The default is off.
Function Button
Mode / Status
( Indicator Light )
Panning mode
Turn on/off
Panning and Tilting mode
Switch operating modes
Standby
For other functions
Lock mode / Initialize the gimbal
The working mode and
Rolling angle adjustment / function can be identified
Initialization failure / Malfunction by the LED status
Camera is permitted to pan left or right and tilt up and down. Rolls are restricted.
Reset
Standby
Function Explanation
Panning Mode / Lock Mode Single tap to switch between panning mode and lock mode
Panning and Tilting Mode Under panning and tilting mode, single tap to switch to lock mode
It is possible to switch to other modes under inversion mode,
Inversion Mode
triple tap again to exit inversion mode and reset
Reset Reset the tilting axis of the gimbal to initial orientation and initial mode
Rolling angle adjustment Please refer to"Gimbal Horizontal Angle Adjustment"for operations
Single tap again to awake the gimbal, or triple tap
Standby
to initialize the gimbal
Power off
Video
GND
Analog Monitor
Video Output Cable
( Equipped By Users )
OFF
Video / SD
V
reading switch
ON
V
GoPro Mini
micro port
C
to Micro port
OFF
GoPro charging
C
switch
ON
Joystick Joystick
Joystick Control
Joystick Direction
Up UP
Down Down
Left Left
Right Right
Reset the tilting axis of the gimbal to initial orientation
and initial mode.
In standby model, keep the gimbal in power-up state,
the motor stops working, the indicator light flashes for
three times, and single tap again to wake the gimbal.
When the gimbal and GoPro are
powered on , connect the Analog
Monitor to the function port with
the Video Output Cable, to output
the video to the Analog Monitor.
Read the GoPro SD card and
charge the GoPro without dismount
the GoPro
PC
USB Cable