Advertisement
Quick Links
3-Axis Handheld Gimbal for iPhone
iPhone 6s Plus / 6s / 6 Plus / 6
iPhone 5s / 5C / 5 / 4s / 4
1.
Product Overview
Rolling
Panning
Joystick
Function Button
( On/Off )
(Indicator light)
LED status
Explanation
Full Power
Blue light flashes for three times
Blue light flashes twice
Enough Power
Blue light flashes once
Low Power
Blue light keeps flashing
No Power
When the red LED indicator light flashes
in use, it means the gimbal is out-of-order
4.
Operating
Function Button
( Indicator Light )
Power on / Power off
Switch the working mode
Realize other functions
Identify the current mode of the
gimbal by the indicator lights
Explanation of LED indicator status
LED status
Mode / Status
Single flash
Panning mode
Double flashes
Panning and Tilting mode
Three flashes
Standby
Always on
Lock mode / Initialize the gimbal
Rolling angle adjustment /
Flash quickly
Initialization failure / Malfunction
Operating Instructions of Function Button
Operation
Function
Single tap
Panning Mode / Lock Mode
Double tap
Panning and Tilting Mode
Triple tap
Inversion Mode
Quadruple tap
Reset
Tap button for six times
Rolling angle adjustment
Long press for 1 second
Standby
Power off
Long press for 3 seconds
Working Modes
Panning Mode
The phone is allowed to pan left or right. Vertical tilts or rolls are restricted.
Panning and Tilting Mode
The phone is allowed to pan left or right and tilt up and down. Rolls are restricted.
Lock Mode
The phone stays in its current orientation. All panning, tilting and rolls are restricted.
Other Functions
Inversion Mode
Three working modes can be switches under inversion mode. After entering into the inversion mode, the
gimbal automatically switches to the panning mode.
Invert the gimbal, put the camera face down to capture the wonderful moments.
The gimbal can restore to the boot-up state by consecutively pressing the function button for three times
under inversion mode.
Manual Pulling Locking
After the gimbal being powered on for eight seconds, pull the tilting axis to the desired angle under non
panning and tilting mode and wait for 0.5 second until the gimbal registers the new angle.
Reset
Reset the tilting axis of the gimbal to initial orientation and initial mode.
Standby
In standby model, keep the gimbal in power-up state, the motor stops working, the indicator light flashes
for three times, and single tap again to wake the gimbal.
Instruction Manual
Tilting Axis
Tilting
Rolling Axis
Panning Axis
Function
Interface
1/4 inch Screw Hole
LED indicator light
Joystick
for
Direction
Control
Explanation of joystick control
Controllable
Movement
Mode
angle of joystick
of joystick
Panning mode
Tilting angle
Up, Down
Panning and
Uncontrollable
Uncontrollable
Tilting mode
Tilting and
Lock mode
Up, Down, Left, Right
panning angle
Explanation
Single tap to switch between panning mode and
lock mode
Under panning and tilting mode, single tap to switch
to lock mode
It is possible to switch to other modes under
inversion mode, triple tap again to exit inversion
mode and reset
Reset the tilting axis of the gimbal to initial
orientation and initial mode.
Please refer to"Gimbal Horizontal Angle Adjustment"
for operations
Single tap again to awake the gimbal, or triple tap
to initialize the gimbal
2. Accessories
Charger
Rechargeable
Battery
Input: DC 5V
Type:18350
Output: DC 4.2V
How to Charge
USB Cable
Charger
3.
User Guide
(1) Please install the iPhone before powering on the gimbal.
Attention !
!
(2) Please turn off the power when not in use.
Install the batteries
1
Remove the power switch cap, and
insert two 18350 batteries into the handle.
3
Adjust the phone position and install the counter-weight
1mm Counter-Weight
Light
iPhone 6s
iPhone 6s Plus
0 mm
Light
iPhone 6
iPhone 6 Plus
0 mm
How to install iPhone6s / 6
How to install iPhone 6s Plus / 6 Plus
Use the light counter-weight,
Use the heavy counter-weight,
attach the bottom of the phone to
attach the bottom of the phone to the
the motor of tilting axis.
motor of tilting axis, as shown in the
picture.
Power on / off
4
Power On: Single tap the function button, the gimbal shall be powered on after 2 seconds.
Power Off: Hold down the function button for three seconds to turn off the gimbal.
Attention: Turn the gimbal on after ensuring the phone is secure.
5.
Gimbal Horizontal Angle Adjustment
The horizontal angle needs to be adjusted whenever the following situations happen to the gimbal, user can
adjust the horizontal angle by gimbal initialization and joystick.
（1）The tilt angle is not leveled with the horizontal surface.
（2）The roll angle is not parallel to the horizontal surface.
（3）Under lock mode, the panning angle drifts.
Adjusting steps:
STEP 1
Initialize the gimbal
After finished the
, the rolling angle still not parallel to the horizontal surface, you can use the joystick
STEP 1
to adjust the rolling angle according to
STEP 2
Rolling angle adjustment
STEP 2
Tap button for six times for roll angle adjustment, the tilt and roll angle restore to the horizontal status. Under the roll
angle adjustment state, move the joystick to the left or to the right to adjust the roll angle, single tap again to save the
setting and exit after adjusting.
6.
Parameters
Vertical Titling Angle
320°
Rolls Angle
100°
Horizontal Panning Angle
360°
Titling Increments
2°/s ~ 75°/s
Panning Increments
3°/s ~ 150°/s
Usage time
4 Hours
Adaption
iPhone 6s Plus / 6s / 6 Plus / 6 / 5c / 5s / 5 / 4s / 4
315g（not including batteries, phone, or counter-weight）
Weight
Heavy Counter-weight 52g
D I S C L A I M E R
G4 Pro 3-Axial handheld gimbal for iPhone is an excellent camera stabilizer, lightweight and portable.
Prohibit any user for any illegal purpose. Users will be responsible for all behaviors of purchase and use products.
The Company assumes no liability for any risks related to or resulting from the debug and use of this product
(including the direct, indirect or third-party losses).
For any unknown sources of using, we will not be at any services.
Feiyu Tech reserves the right to amend this manual and the terms and conditions of use the gimbal at any time.
Attention
Please correctly assemble the gimbal in accordance with the diagram.
Please install the camera before powering on the gimbal.
Please charge the battery with the standard charger.
When the gimbal is not in use or placed on the table, please ensure it is powered off.
Scan and keep
an eye on FY
Please visit the official website of Feiyu Tech
to get related information: www.feiyu-tech.com
Support email: service@feiyu-tech.com
Heavy Counter-Weight
Weight：52 g
Light Counter-Weight
Weight：6 g
1mm Counter-Weight
USB Cable
Weight：8 g
Connect the Mini-USB
port of the USB cable with
the charger, and the USB
port with 5V USB power
adapter.
5V USB
Power Adapter
(Equipped by users)
Install the phone
2
Attach the iPhone by the quick-release adapter,
and ensure it is secure.
Note: Please take off the protective casing of the
phone before installation.
1mm Counter-Weight
iPhone 5
iPhone 4
Heavy
0 mm
Heavy
How to install iPhone 5s / 5c / 5 / 4s / 4
Use the light counter-weight, leave
distances of about 9mm between
the bottom of phone and the motor
of tilting axis, as shown in the picture .
0 mm
.
Light Counter-weight 6g
Light
9 mm
Advertisement
