FeiYu Tech FY G4 Manual

FY G4 is suitable for GoPro 4/GroPro 3+/GroPro 3, also can be compatible
with GoPro LCD backpack and the cameras with the same size.
1
Beginner Guide
Please upgrade the firmware to V1.13 or above version.
Attention ! Please install the suitable camera first before power on the Gimbal.
Remove the power switch
Install the GoPro camera by the
cap, insert two 18350
special Thumb Screw. And make
batteries into the handle.
sure it is fixed well.
Power On
Confirm the camera is
installed well,then press
the power button to turn
on the Gimbal.
2
Product Appearance Instructions
Pitch Axis
Roll Axis
M2 Knurled
Video Input
Thumb Screw
And
Camera
Heading Axis Charging
Interface
Function
Interface
Function
Button
Power
Switch
If any comments or suggestions please do not hesitate
to e-mail us directly : service@feiyu-tech.com
EN
FEIYU-EN-3
R L
Installation
Method
Please choose one way
to install the GoPro camera
Mode Switching
When the Gimbal is working, you
can press the function button to
switch among the three working
modes and a special working
condition.
(Details of working modes please refer
to the instructions of working modes)
Indicator
Indicator Explanation
LED Status Explain
Blue light flashes
Full Power
three times
Blue light flashes
Enough Power
twice
Blue light flashes
Low Power
once
Blue light keeps
No Power
flashing
If the indicator light flashes red,
the Gimbal will not work correctly
due to an error.
3
Operation Instructions
Function Button Working Mode Instructions
Use for switch
Heading Follow Mode
the working
constant, heading follows the handheld position.
mode and
Heading And Pitch Follow Mode
realize other
functions
constant. Heading and Pitch follow the handheld position.
Heading Lock Mode
The working mode and function
point at one position.
can be identified by the LED status
Special Working Condition (Inversion Mode) When in any working mode, press the function button for three times in succession, the
Gimbal will enter into the inversion mode and switch to the Heading following mode automatically. Invert the Gimbal to capture more excited
scenes easily by switching mode combination. When in inversion working condition press the function button for three times in succession to reset
the Gimbal back to the original state.
Standby Mode Press the function button for 3 seconds, then the motor will stop working and the LED of the function button will light constantly.
This indicates that the Gimbal is in the standby mode. Single press the function button the Gimbal will be awakened immediately.
The pitching can be adjusted 8 seconds after the Gimbal has been started. Within the Heading Follow and Heading
Manual Pulling Locking
Lock Mode the pitching can be adjusted to the desired angle manually, wait in this position up to 0.5 second until the current angle is adjusted.
Four press the function button in succession within any working mode, the gimbal will reset to the original state.
Reset
The pitch and roll angle can be adjusted to level by G4 Remote Control without connect to the computer. Details of the
Level Calibration
operation please refer to chapter
6
Heading Follow Speed Mode Configuration The follow speed of the heading can be configurate by G4 Remote Control without
connect to the computer. Details of the operation please refer to chapter
Function Button Instructions
Operation LED Status Function Explanation
Single Press Single Flashes Heading Follow Mode
Double Press Double Flashes Heading And Pitch Follow Mode
Three Press Single Flashes Inversion Mode
Four Press Single Flashes Reset
Long Press
On Constantly Heading Lock Mode
For 1 Second
Long Press
On Constantly Standby Mode
For 3 Second
4
Standard And Optional Accessories
Standard Accessories
Extension Knurled
Thumb Screw
Rechargeable
Charger
Battery
USB Connector
Input: DC 5V
Output: DC 4.2V Type: 18350
USB
Camera Charging Cable
Mini-USB
USB Cable Video Output Cable
Camera Pitch and Roll Angles remain
Camera Roll Angle remains
Heading, Pitch and Roll are all locked to
6
Operation Again
Function Of Operation Again
Other operation is arbitrary
Other operation is arbitrary
Three Press again Exit inversion mode to original state
Other operation is arbitrary
Other operation is arbitrary
Exit standby mode ,
Single press again
and awaken immediately
Correct Method for Using USB Data Cable
Please refer to the method of proper usage
!
mentioned below. Otherwise the device
itself or other equipments can be damaged
Battery Charging:
Put the Mini-USB terminal of the USB cable
into the Mini-USB interface of the charger and the USB terminal to
the power adapter which with the USB interface(Equipped by users)
If needed connect to the EU connector (Equipped by users).
Connect The Computer: Please remove the batteries first,
then insert the Mini-USB terminal into the function interface on the
Gimbal and the USB terminal to the USB connector. Afterwards
connect the device with the computer to do firmware updates or
parameter configuration.
Further information can be found in the chapter of the
Function Interface Instructions.
Optional Accessories
Name Function Description
Realize the heading & pitch angle adjustment,
Remote
mode switching, level calibration and heading
Control
follow speed configuration from a distance.
Extend the capacity space for battery to
Battery
Extender make the runtime longer.
Spiral design of the extension bar can be
perfect combination with G4 power switch；
Extension
Extended length is optional, it will help to
Bar
enjoy a different visual easily.
Heading