EVERSPRING AN179 Manual

AN179
TM
The In-Wall On/Off Module is a Z-Wave enabled device which is fully compatible with any Z enabled device which is fully compatible with any Z-Wave
TM
enabled network. Z-Wave enabled devices displaying the Z-Wave
regardless of the manufacturer, and ours can also be used in other manufacturer's Z , and ours can also be used in other manufacturer's Z-Wave
networks. Inclusion of this unit on other manufacturer's Wireless Controller menu allows remote operation on other manufacturer's Wireless Controller menu allows remote operation
of the unit and the connected load.
The In-Wall On/Off Module is designed to control the on/off status of lighting and appliances
house. Two sets of dry contacts provide more wiring applications. For security, t
overheating and will turn off relay automatically to avoid damage. At 230V voltage, t
up to 2500W resistive, 1200W incandescent, 700W motor, or 320W (40W*8) fluorescent
Product Overview
TM
Adding to Z-Wave Network
On the unit you can find a link key which is used to carry out the function of inclusio a link key which is used to carry out the function of inclusion, exclusion, and reset.
When power is applied for the first time, the LED will flash on and off alternately and repeatedly, implying that is applied for the first time, the LED will flash on and off alternately and repeatedly, implying that
it has not yet been assigned a node ID and cannot work with other Z-Wave enabled devices.
supports the Auto Inclusion function when power is applied and no node ID is stored in the memory. to Inclusion function when power is applied and no node ID is stored in the memory.
Auto Inclusion
The module may automatically execute the function of inclusion when...
1. The power is applied for the first time and no node ID has been stored in the is applied for the first time and no node ID has been stored in the module.
2. The execution of reset is successful where the stored node ID is cleared.
Note: The duration for Auto Inclusion is about 4 minutes. Unlike the "inclusion" procedure shown in the
table below, the execution of Auto Inclusion is automatic without the necessity of pressing the link key.
Action/Status Description
The Z-Wave Controller does not allocate a node ID to the Wave Controller does not allocate a node ID to the
No node ID
unit.
The power is applied for the first time and no node ID has is applied for the first time and no node ID has
Auto Inclusion
been stored in the module, or after executing reset.
1. Put the Z-Wave Controller into inclusion mode.
Inclusion 2. Press the link key three times within 1.5 seconds to Press the link key three times within 1.5 seconds to
put the unit into inclusion mode.
1. Put the Z-Wave Controller into exclusion mode.
Exclusion
2. Press the link key three times within 1.5 seconds to Press the link key three times within 1.5 seconds to
put the unit into exclusion mode.
1. Press the link key three times within 1.5 seconds to
Reset
put the unit into exclusion mode.
(This procedure
should only be used
2. Within 1 second of step 1, press link key again and
when the network
hold until LED is off (about 5 seconds).
In-Wall On/Off Module
TM
logo can also be used with it logo can also be used with it
lighting and appliances load in your
or security, the unit can detect
At 230V voltage, this module can support
fluorescent load.
Dry Contact
LED Light
RF Aerial
Link Key
Wiring
Terminals
Wave enabled devices. This unit
4 minutes. Unlike the "inclusion" procedure shown in the
e necessity of pressing the link key.
clusion mode.
ds to
press link key again and
primary controller is
inoperable.)
Failed or successful results in including/excluding the ID can be viewed on the Z Failed or successful results in including/excluding the ID can be viewed on the Z-Wave Controller.
TM
Safety Precautions & Installation
TM
enabled
Avoid installing the unit in storming or raining weather. Avoid installing the unit in storming or raining weather.
Be sure to isolate or switch off power source before installing or maintenance. Be sure to isolate or switch off power source befor
DO ensure that the power supply circuit is pro
fuse.
IMPORTANT
Installation must be performed by skilled technicians who are informed about the standards and Installation must be performed by skilled technicians who are informed about the standards and
technical requirements of the appliance and its proper installation. requirements of the appliance and its proper installation.
Check your local codes as they apply to your situation. If the house wiring is of aluminum, consult Check your local codes as they apply to your situation. If the house wiring is of aluminum, consult
with an electrician about proper wiring methods.
Before proceeding with the installation, TURN OFF THE POWER TO THE LIGHTING CIRCUIT AT
THE CIRCUIT BREAKER OR FUSE BOX TO AVOID ELECTRICAL SHOCK. THE CIRCUIT BREAKER OR FUSE BOX TO AVOID ELECTRICAL SHOCK.
The In-Wall On/Off Module supports 2 sets of dry contacts
wiring accordingly.
As illustrated in the above diagram, S1 provides a wall switch connection to the dry contacts. By default
switch supports Single-Pole-Double-Throw (SPDT
Gateway, S1 can be configured to support Toggle switches as well. The S2 switch can also switch the Gateway, S1 can be configured to support Toggle switches as well.
on/off status of the unit when toggled.
Operation
Under normal operation mode, press the button on
The LED indicator will also turn on or off accordingly. The u
LED indication
signals from the Z-Wave Controller.
2-second on,
The unit is able to remember the status of the relay when power is cut off (such as power black-out). When The unit is able to remember the status of the relay when power is cut off (such as power black
2-second off
power is supplied again, the unit will resume the last status of the relay (on or off) automatically. power is supplied again, the unit will resume the last status o
Note: Pressing the button on the unit for over 5
operation mode of the dry contacts. The LED will flash 3 times rapidly upon successful switch.
Programming
Z-Wave Group Support
The unit supports two association groups with 1
Grouping 2. This has the effect that when the u
receive the relevant reports.
3. Node ID is excluded ode ID is excluded. The device reverts to factory
default state and will be in auto and will be in auto-inclusion mode for 4
minutes.
rotected by a 16 amp circuit breaker or suitable equivalent
FF THE POWER TO THE LIGHTING CIRCUIT AT
2 sets of dry contacts. Study the following figure and implement the
diagram, S1 provides a wall switch connection to the dry contacts. By default S1
T) type of binary switch. However, through the setting of
on the unit to control the on/off status of the connected load.
also turn on or off accordingly. The unit can also be controlled by receiving command
r 5 seconds but no more than 8 seconds can switch the
he LED will flash 3 times rapidly upon successful switch.
1 node support for Grouping 1 and 4 nodes support for
unit is operating, all devices associated with the unit will