Table of Contents
Advertisement
Quick Links
HDW-2
IMPORTANT: DO NOT DISCARD THIS MANUAL
This manual is considered to be part of the appliance and is to be given to the OWNER or
MANAGER of the restaurant, or to the person responsible for TRAINING OPERATORS of
this appliance. Additional manuals are available from your WELLS DEALER.
THIS MANUAL MUST BE READ AND UNDERSTOOD BY ALL PERSONS USING OR
INSTALLING THIS APPLIANCE. Contact your WELLS DEALER if you have any
questions concerning installation, operation or maintenance of this equipment.
p/n
Rev. (C)
2M-Z14353
WELLS MANUFACTURING
10 Sunnen Dr., St. Louis, MO 63143
telephone: 314-678-6314
fax: 314-781-2714
www.wellsbloomfield.com
OWNERS MANUAL
BUILT-IN
DISHER WELL
WARMER
MODELS
HDW-2
HDW-2D
Includes
INSTALLATION
USE & CARE
EXPLODED VIEW
PARTS LIST
WIRING DIAGRAM
M025
14
025
0224
Advertisement
Table of Contents
Related Manuals for Wells HDW-2D
Summary of Contents for Wells HDW-2D
- Page 1 Additional manuals are available from your WELLS DEALER. THIS MANUAL MUST BE READ AND UNDERSTOOD BY ALL PERSONS USING OR INSTALLING THIS APPLIANCE. Contact your WELLS DEALER if you have any questions concerning installation, operation or maintenance of this equipment.
-
Page 2: Warranty
LIMITED WARRANTY STATEMENT Unless otherwise specified, all commercial cooking prices charged by Wells Manufacturing for its products are equipment manufactured by Wells Manufacturing is based upon the limitations in this warranty. Seller’s obligation warranted against defects in materials and workmanship... -
Page 3: Table Of Contents
PARTS & SERVICE CUSTOMER SERVICE DATA INTRODUCTION Thank You for purchasing this Wells Manufacturing appliance. Proper installation, professional operation and consistent maintenance of this appliance will ensure that it gives you the very best performance and a long, economical service life. -
Page 4: Features & Operating Controls
FEATURES & OPERATING CONTROLS Faucet Stand Pipe & (optional with some models) Drian Overflow Lighted Power Switch IL2157a See Detail 3/4” Drain Power Cord Nameplate MOUNTING BRACKET Detail A. CONTROLS Units are equipped with a lighted power switch which illuminates when the unit is turned on. -
Page 5: Precautions & General Information
Do not operate this appliance if the control panel is damaged. read and followed. Damage Call your Authorized Wells Service Agent for service. to the appliance may result The technical content of this manual, including any wiring diagrams,... -
Page 6: Installation
Cutout dimensions for disher well and optional faucet are listed on the Installation Instructions provided with the warmer. NOTE: Verify the dimensions are correct for the installation before OPTIONAL FAUCET 0.875” for Wells Supplied making the cutout. Faucet Other Faucets 3 1/8”... - Page 7 INSTALLATION ELECTRICAL INSTALLATION CAUTION: 1. Refer to the product nameplate. Verify the electrical service power. SHOCk HAzARD Voltage and phase must match the nameplate specifications. The ground lug of this Wiring the warmer to the wrong voltage can severely damage the appliance must be connected unit or cause noticeably decreased performance.
-
Page 8: Operation
OPERATION CAUTION: WET OPERATION for DISHER WELL This unit is designed to be used for WET operation, add tap water HOT SURFACE Allow the disher well to preheat for before turning the warmer on. approximately 30 minutes prior to using. Exposed surfaces can be hot to the touch and may cause Check the water level frequently and add water as necessary... -
Page 9: Maintenance Instructions
Never use metal implements, wire brushes, abrasive scratch pads or steel wool to clean stainless steel. Warmer pans, insets and other vessels are subject to a harsher environment. Wells Manufacturing uses an very high quality stainless steel (#304DDQ) for our food warmer pans. -
Page 10: Cleaning Instructions
CLEANING INSTRUCTIONS DAILY CLEANING INSTRUCTIONS CAUTION SHOCk HAzARD PREPARATIONS: Turn main power switch to OFF. Allow warmer to cool before proceeding. Do NOT splash or pour water Remove any insets, utinsils and/or inserts. into or over any control panel Drain or remove water from well.. or wiring. - Page 11 CLEANING INSTRUCTIONS MONTHLY CLEANING INSTRUCTIONS CAUTION: CHEMICAL BURN PREPARATIONS: Remove any insets, utinsils. HAzARD Drain or remove water from well. Deilimng chemicals may be caustic. Wear appropriate Weekly, or whenever lime or scale is seen FREQUENCY: personal protective equipment. accumulating on the sides of the warmer pans. Follow cleaner manufacturer’s instructions for safest use.
-
Page 12: Troubleshooting Suggestions
Drain-equipped unit will not hold water Contact your Authorized Wells Service Drain valve damaged or pan(s) leaking Agency for repairs There are no user-serviceable components in this appliance. In all instances of damage or malfunction, contact your Authorized Wells Service Agency for repairs. -
Page 13: Wiring Diagram
WIRING DIAGRAM POWER SWITCH THERMOSTAT HIGH LIMIT THERMOSTAT HEATING ELEMENT WHITE BLACK GROUND HDW-2 Wiring Diagram SK2488... -
Page 14: Exploded View & Parts List
EXPLODED VIEW: HDW-2 DISHER WELL Model: HDW-2 DISHER WELL SK2489, Rev. B, 2/24/2014... - Page 15 SCREW #8 -32 X .5 RH NP P2-Z14506 BRACKET - HIGH LIMIT 2T-Z14503 THERMOSTAT 325°F 2C-73457 8-32 KEPS NUT SS P2-Z14189 CLAMP BOWL 2M-Z14204 LABEL - WELLS LOGO AND CAUTION 2E-Z14201 SWITCH, STST-LIGHTED P2-Z14193 WIRE CHANNEL P2-Z18249 WIRE COVER 2C-1810 WASHER 3/16” STL...
- Page 16 NOTES...
- Page 17 NOTES...
- Page 18 NOTES...
-
Page 19: Parts & Service
PART NO. authorized service parts and replacement filters. For factory authorized service, or to order factory authorized replacement parts, contact your Wells authorized service agency, or call: Wells Manufacturing 10 Sunnen Dr., St. Louis MO 63143 USA Service Dept. phone: (314) 678-6314... - Page 20 WELLS MANUFACTURING 10 Sunnen Dr., St. Louis, MO 63143 telephone: 314-678-6314 fax: 314-781-2714 www.wellsbloomfield.com...