Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Doyon Artisan
Summary of Contents for Doyon Artisan
- Page 1 Doyon Artisan Instruction Manual...
-
Page 2: Table Of Contents
MODULRAM DIGITAL | Edition A - Revision 0 Table of contents 01. Oven technical information · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 3 02. -
Page 3: Oven Technical Information
MODULRAM DIGITAL | Edition A - Revision 0 1 | Oven technical information Oven ManufaCturer: Doyon & Nu-Vu 5600 13th Street Menominee, MI, USA 49858 Tel. 1-800-338-9886 www.Doyon.qc.ca Instruction Manual | 3... - Page 4 MODULRAM DIGITAL | Edition A - Revision 0 Oven with control panel 9080 Instruction Manual | 4...
-
Page 5: Connections To Be Made To The Oven (Control Panel Ele.d14)
MODULRAM DIGITAL | Edition A - Revision 0 2 | Connections to be made to the oven (control panel 9080) 2.1 SteaM, Water, DraIn anD eLeCtrICaL COnneCtIOnS STEAM OUTPUT To ensure a successful baking process, the steam output must be independent from the exhaust output. Install an aluminum tube of 80mm in diameter to separate the steam output from the exhaust output. -
Page 6: First Time Heating Process (Control Panel Ele.d14)
MODULRAM DIGITAL | Edition A - Revision 0 3 | First time heating process (control panel 8090) When the oven is turned on for the first time it will corded with a 25ºC margin. To start this programme press automatically enter Ramalhos mode... -
Page 7: Description Of Control Panel Display Ele.d14
MODULRAM DIGITAL | Edition A - Revision 0 4 | Description display of control panel 9080 tOP DISPLaY CLOCK DISPLaY StOne DISPLaY ButtOn tO InCreaSe nuMBerS ButtOn tO DeCreaSe nuMBerS tOP teMPerature ButtOn StOne teMPerature ButtOn ButtOn fOr frOnt-tOP POWer anD frOnt-StOne CLOCK ButtOn SteaM InjeCtIOn ButtOn... -
Page 8: Operation Of Control Panel Ele.d14
MODULRAM DIGITAL | Edition A - Revision 0 When the baking cycle starts, the timer will show the remain- 4.1 OPeratIOn Of COntrOL PaneL 9080 ing time until 0 is reached. An acoustic signal indicating the end of the baking cycle will be heard. This signal is activated The control panel will automatically carry out a series of ac- intermittently by the relay and is on for the pre-set period of tions which ease the baking process. -
Page 9: Programming Automatic Start-Up
MODULRAM DIGITAL | Edition A - Revision 0 Throughout this process the button and the let- 4.3 PrOgraMMIng autOMatIC Start-uP ter on the hour display will flash. When the timer reaches 0, the control panel will turn on au- The automatic start-up enables the control panel to turn on tomatically. -
Page 10: Breakdown Warning Messages
MODULRAM DIGITAL | Edition A - Revision 0 4.5 BreaKDOWn WarnIng MeSSageS Some breakdowns will activate a warning message that shows up on some displays. The warning relay will also be activated until the breakdown is acknowledged and a button is pressed. The warning relay will then be deactivated but the warning message will continue showing on the display until the problem is solved. -
Page 11: Solutions To Problems
MODULRAM DIGITAL | Edition A - Revision 0 4.6 SOLutIOnS tO PrOBLeMS Breakdowns Problem Solution · the light in one of the 1. Light bulbs are burnt out. 1. Substitute the burnt out light bulbs. chambers does not turn on ·... -
Page 12: Oven Maintenance (Control Panel Ele.d14)
MODULRAM DIGITAL | Edition A - Revision 0 5 | Oven Maintenance (control panel 9080) 5.1 generaL CLeanIng Of tHe Oven 5.3 MaIntenanCe Of gLaSS DOOrS The oven must be cleaned on a regular basis and whenever CLeanIng tHe gLaSS DOOrS needed to prevent the formation of crusts that cannot be ea- With time the glass doors build up sediments. -
Page 13: Substituting Light Bulbs
MODULRAM DIGITAL | Edition A - Revision 0 5.4 SuBStItutIng LIgHt BuLBS 5.6 CLeanIng tHe SteaMerS (OPtIOn) Light bulbs can only be substituted with bulbs that are 12 volts; 20 Watts, if not, the lighting system can be damaged fig. 6.1 fig. -
Page 14: Cleaning The Solenoid
MODULRAM DIGITAL | Edition A - Revision 0 5.7 CLeanIng tHe SOLenOID When the solenoid allows water to pass it is necessary to clean It is also possible that the seal is damaged (fig. 7.5). In this case, it its interior. is necessary to substitute the part. -
Page 15: Table Of Maintenance Frequency
MODULRAM DIGITAL | Edition A - Revision 0 5.8 taBLe Of MaIntenanCe frequenCY Maintenance Frequency How to do it · Steamers Biannually See page 13 (cleaning steamers). · Stones Daily Vacuum all of the stones. · Chambers Weekly Should be heated up to baking temperature espe- cially when they have been stopped for a long time in order to avoid oxidation. -
Page 16: Description Of The Front Panel Of The Prover Control Panel
MODULRAM DIGITAL | Edition A - Revision 0 6 | Description of the front panel of the proofer control panel TEMPERATURE DISPLAY HUMIDITY BUTTON Digital display for viewing prover temperature. This button has two functions. Pressing once allows for the editing of the humidity level inside the prover. A pro- HUMIDITY DISPLAY longed pressing will turn the production of humidity ON Digital display for viewing prover humidity. -
Page 17: Programming The Control Panel Of The Prover
MODULRAM DIGITAL | Edition A - Revision 0 6.1 PrOgraMMIng tHe COntrOL PaneL Of tHe PrOver 6.2 MaIntenanCe Of tHe PrOver With the control panel ON, select the desired temperature CLeanIng tHe SePtIC BOX and humidity levels. The control panel will maintain these pa- rameters until they have been changed by the user. -
Page 18: Possible Breakdowns Of The Prover Control Panel
MODULRAM DIGITAL | Edition A - Revision 0 6.3 POSSIBLe BreaKDOWnS Of tHe PrOver COntrOL PaneL If a breakdown is detected, the error will appear on the temperature screen. The table below shows the solutions to the different breakdowns Error message Causes Solution Temperature probe.
Need help?
Do you have a question about the Artisan and is the answer not in the manual?
Questions and answers