1. Manuals
  2. Brands
  3. Lectrosonics Manuals
  4. Transmitter
  5. Digital Hybrid Wireless DBu
  6. Quick start manual

Lectrosonics Digital Hybrid Wireless DBu Quick Start Manual

Digital belt pack transmitter
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Q
uick
S
tart
G
uide
Digital Belt Pack Transmitter
Fill in for your records:
Serial Number:
Purchase Date:
Digital Hybrid Wireless
This guide is intended to assist with
initial setup and operation of your
Lectrosonics product.
For a detailed user manual, down-
load the most current
version at:
www.lectrosonics.com
US Patent 7,225,135
®
31 May 2019

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Digital Hybrid Wireless DBu and is the answer not in the manual?

Questions and answers

Related Manuals for Lectrosonics Digital Hybrid Wireless DBu

Summary of Contents for Lectrosonics Digital Hybrid Wireless DBu

  • Page 1 US Patent 7,225,135 ® Fill in for your records: This guide is intended to assist with initial setup and operation of your Serial Number: Lectrosonics product. For a detailed user manual, down- load the most current version at: Purchase Date: www.lectrosonics.com...
  • Page 2 Function Switch Antenna AUDIO Audio Port Input IR PORT Jack PWR/FUNC Key verification Battery status LED 470.100 Menu navigation buttons Return to previous screen Power button Belt clip Belt clip mounting hole mounting hole USB Port Battery compartment door LECTROSONICS, INC.
  • Page 3 The IR port is available on the top of the transmitter for quick setup using a receiver with this function available. IR Sync will transfer the settings for fre- quency from the receiver to the transmitter. Remove hole cap to attach spring loaded belt clip www.lectrosonics.com...

  • Page 4: Battery Installation

    Slide door out to release catch Lift door to open Insert the batteries according to the markings on the back of the housing. If the batteries are inserted incorrectly, the door will close but the unit will not operate. LECTROSONICS, INC.

  • Page 5: Battery Status Led Indicator

    BatTime function to determine remaining runtime. NOTE: Refer to the Main Menu and Setup Section for BatTime details. www.lectrosonics.com...

  • Page 6: Powering On In Operating Mode

    NOTE: If the programmable switch is in the OFF position, power can still be turned on with the power button. If the programmable switch is then turned on, a brief message will appear on the LCD. LECTROSONICS, INC.

  • Page 7: Power Menu Options

    (works in the operating mode only) • Backlit - adjusts the duration of the LCD back light to 5 seconds or 30 seconds, or to remain on About - displays model number and firmware • version www.lectrosonics.com...

  • Page 8: Lcd Menu Map

    (Universal, Shared, Standard or Volatile) BACK WipeKey? Select option with arrow buttons WipeKey (Only available when KeyType is set to BACK Standard, Shared or Volatile) SendKey MENU SendKey Press to send key BACK Share (Only available when KeyType is set to Shared) LECTROSONICS, INC.

  • Page 9: Main Menu And Setup Screen Details

    MUTE word MUTE will blink at the 470.100 bottom of the display. The -10 LED on the top panel <–MUTE–> will also glow solid red. www.lectrosonics.com...

  • Page 10: Connecting The Signal Source

    6) If the audio output level of the receiver is too high or low, use only the controls on the receiver to make adjustments. Always leave the trans- mitter gain adjustment set according to these instructions, and do not change it to adjust the audio output level of the receiver. LECTROSONICS, INC.

  • Page 11: Selecting Programmable Switch Functions

    Low frequency audio content may be desirable or 70 Hz distracting, so the point at which the roll-off takes place can be set to 20, 35, 50, 70, 100, 120 or 150 Hz. www.lectrosonics.com...

  • Page 12: Setting Transmitter Output Power

    Setting Transmitter Output Power The output power can be set to 25 mW or 50 mW. Rolloff TxPower Phase 25 mW BatType 50 mW TxPower Remote Remote control “dweedle” tones from a smart phone can be used to control the transmitter. LECTROSONICS, INC.

  • Page 13: Locking/Unlocking Changes To Settings

    Programmable switch still works (Mute and On/Off) • Power can still be turned off by using the power menu or removing the batteries. Restoring Default Settings This is used to restore the factory settings. Remote Default Locked? settings Default KeyType www.lectrosonics.com...
  • Page 14 SEND KEY is available to transfer the key to another device. • Universal: This is the most convenient encryption option available. All encryption-capable Lectrosonics transmitters and receivers contain the Universal Key. The key does not have to be generated by a receiver. Sim- ply set the DBu and a Lecrosonics receiver to Universal, and the encryp- tion is in place.

  • Page 15: Whip Antennas

    This connection can also be used to send the transmitter settings stored in the receiver to the transmitter. The interface cable, P/N DRKEYCABLE, is used to make this connection. NOTE: Reference the DSW System Instruction Manual for instructions on Encryption Key settings and software. www.lectrosonics.com...

This manual is also suitable for:

Dbu/e01

Table of Contents