C4 Foreseeable Improper Use; C5 Residual Risks - Electrolux EGWSSIC Manual

ATTENTION!
Before carrying out any opera-
tion on the machine, always
consult the manual, which
gives the correct procedures
and contains important infor-
mation on safety.
C4 Foreseeable improper use
Improper use is any use different from that specified in
this manual. During machine operation, other types of
work or activities considered improper and that in gen-
eral can involve risks for the safety of operators and
damage to the system are not allowed.
Foreseeable improper use includes:
• failure to disconnect the power supply (with main
switch in off position "O") before carrying out adjust-
ment, cleaning, resetting and maintenance opera-
tions;
• failure to disconnect the power supply (with main
switch in off position "O") at the end of the day;
• lack of machine maintenance, cleaning and periodi-
cal checks;
• structural changes or modifications to the operating
logic;
• tampering with the guards or safety devices;
• failure to use personal protection equipment by
operators, specialized technicians and mainte-
nance personnel;
• failure to use suitable accessories (e.g. the use of
equipment, ladders unsuitable for carrying out
maintenance to equipment inside the machine);
• keeping combustible or flammable materials, or in
any case materials not compatible with or pertinent
to the work, near the machine;
• incorrect machine installation (see section E "Instal-
lation and assembly");
• placing in the machine any objects or things not
compatible with washing or that can obstruct/dam-
age the machine or persons or pollute the environ-
ment;
• non-compliance with the requirements for correct
machine use;
• other actions that give rise to risks not eliminable by
the Manufacturer.
ATTENTION!
The previously
actions are prohibited!
C5 Residual risks
The machine has several risks that were not com-
pletely eliminated from a design standpoint or with the
installation of adequate protection devices.
10
Nevertheless, through this manual the Manufacturer
has taken steps to inform operators of such risks, care-
fully indicating the personal protection equipment to be
used by them.
Sufficient spaces are provided for during the machine
installation stages in order to limit these risks.
To preserve these conditions, corridors and areas
around the machine must always be:
•
•
•
For the Customer's complete information, the residual
risks remaining on the machine are given below: such
actions are deemed improper and therefore strictly for-
bidden.
APPLICATION PHASE
M=Maintenance, P=Cleaning.
described
kept free of obstacles (e.g. ladders, tools, contain-
ers, boxes, etc.);
clean and dry;
well lit.
: I=Installation, U=Normal use,
RESIDUAL DESCRIPTION OF HAZARDOUS
RISK SITUATION
Slipping or The operator can slip due to water or dirt
falling on the floor.
[ U - M ]
Burns The operator deliberately or unintention-
ally touches some parts inside the
[ U - M - P ]
machine or dishes at the outfeed without
using gloves or without allowing them to
cool.
Electrocu- Contact with live parts during mainte-
tion nance operations carried out with the
electrical panel powered. The operator
[ M ]
intervenes (with a power tool or without
disconnecting the power to the machine)
lying down on the wet floor.
Falling from The operator intervenes on the machine
above using unsuitable systems to access the
upper part (e.g. rung ladders, or climbs
[ I - U - M ]
on it).
Tipping of During maintenance on the machine, or
loads moving its packing, using unsuitable
accessories or lifting systems or with
[ I - M ]
load unbalanced.
Chemical Contact
(e.g. detergent, rinse aid, scale remover,
[ I - U - M - P ]
etc.) without taking adequate safety pre-
cautions. Therefore always refer to the
safety data sheets and labels on the
products used.
Crushing or Possible risk of injury to upper limbs
shearing during the hood closing operation.
[ I - U - M ]
Table 1Residual risks
with chemical substances