J11 Troubleshooting; J12 Machine Disposal - Electrolux EGWSSIC Manual

J11 Troubleshooting
THE DISHWASHER DOES NOT SWITCH ON
1. Make sure the socket is powered.
2. Make sure the plug is properly inserted in the power
socket.
3. Check the fuse. If necessary replace it.
THE DISHWASHER DOES NOT FILL WITH WATER
1. Make sure that the water tap is open.
2. Make sure that the filter in the inlet hose and the filter
in the water solenoid valve are not clogged.
3. Make sure that the inlet hose has no kinks or bends.
THE DISHWASHER MAKES EXCESSIVE NOISE
1. Check possible contact with furniture or sheet metal
that could cause noise or vibrations.
2. Make sure that the glasses or dishes are correctly and
stably loaded on the basket.
WATER LEKEGES UNDER THE DISHWASHER
1. Check possible contact with furniture or sheet metal
that could cause noise or vibrations.
2. Make sure that the drain hose is not blocked and cor-
rectly installed.
3. Make sure that the water inlet hose is correctly
installed and not damaged;
THE DISHWASHER DOES NOT WASH PROPERLY
1. Check the suction filter and carefully clean it if dirty.
2. Make sure the wash jets are not clogged by solid
residuals.
3. Make sure the initial quantity of detergent and/or sub-
sequent additions are correct.
4. The wash cycle used is too short. Repeat the cycle.
5. Make sure the tank temperature is at least 55°C /
131°F.
6. Make sure the dishes are correctly placed in the racks.
THE DISHWASHER DOES NOT WASH PROPERLY
1. Check the suction filter and carefully clean it if dirty.
2. Make sure the wash jets are not clogged by solid
residuals.
3. Make sure the initial quantity of detergent and/or sub-
sequent additions are correct.
4. The wash cycle used is too short. Repeat the cycle.
5. Make sure the tank temperature is at least 55°C /
131°F.
6. Make sure the dishes are correctly placed in the racks.
GLASSES AND DISHES ARE NOT PROPERLY DRIED
1. Make sure there is rinse aid in the container and top-
up if necessary.
2. Check the amount of rinse aid used.
3. Make sure the rinse water temperature is between
80°C and 90°C.
CONDENSATE ON GLASSES
1. Make sure there is rinse aid in the container and top-
up if necessary.
2. Check the amount of rinse aid used (see paragraph
I3.1).
3. Remove the rack of the glasses immediately after the end
of the cycle.
STAINS ON GLASSES
1. Only use "non-foaming" products for professional
dishwashers.
EXCESSIVE FOAM IN THE TANK
1. Make sure the wash water temperature is not below
55°C / 131°F.
2. Check if the detergent dispenser delivers an excessive
dose of product (see paragraph I3.2).
3. Make sure the tank has been cleaned with suitable
detergents. Empty the tank and rinse thoroughly
before doing other wash cycles.
4. If a foaming detergent was used, empty and refill the
tank with water until the foam has disappeared.
GLASSES WITH STREAKS OR SPOTS
1. Reduce the amount of rinse aid (see paragraph I3.1).
THE WASH AND/OR RINSE ARMS TURN SLOWLY
1. Remove the arms and clean them thoroughly.
2. Clean the wash pump suction filter.
J12 Machine disposal
At the end of the product's life-cycle, make sure it is not
dispersed in the environment. The equipment must be
disposed of in compliance with the regulations in force
in the country of use.
All metal parts are in stainless steel (AISI 304) and
removable. Plastic parts are marked with the letters of
the material.
The symbol on the product indicates that it should
not be treated as domestic waste, but must be cor-
rectly disposed of in order to prevent any negative con-
sequences for the environment and human health.
For further information on the recycling of this product,
contact the local dealer or agent, the after-sales assis-
tance service or the local body responsible for waste
disposal.
ATTENTION!
When scrapping the machine,
the marking CE must be
destroyed.
25