Omron S8VK-S Series Manual page 2

S8VK-S
Specifications
Ratings, Characteristics, and Functions
Item
Efficiency
Voltage range *2
Frequency *2
Input current
Input Power factor
Leakage current *3
Inrush current *4 (for a
cold start at 25°C)
Rated output current
Rated output electric power
Maximum boost current
Voltage adjustment range *5
Ripple & Noise voltage
*6
Input variation influence *7
Output
Load variation influence *8
Temperature variation
influence
Start up time *4
Hold time *6
Overload protection
Overvoltage protection *9
Additional
Series operation
functions
Parallel operation
Output indicator
Low-voltage detection output
Withstand voltage
Insulation
Insulation resistance
Ambient operating temperature *10
Storage temperature
Environment
Ambient operating humidity
Vibration resistance
Shock resistance
MTBF
Reliability
Life expectancy *11
Weight
Construction Cooling fan
Degree of protection
Harmonic current emissions
EMI
EMS
Approved Standards
Standards
Conformed Standards
Marine Standards *12
SEMI
Note: For notes *1 to *12, refer to page 4.
2
Power rating
Output voltage
115 VAC input *1 87% typ.
230 VAC input *1 86% typ.
Single-phase, 85 to 264 VAC, 90 to 350 VDC
50/60 Hz (47 to 450 Hz)
115 VAC input *1
0.58A typ.
230 VAC input *1 0.36A typ.
115 VAC input 0.5 mA max.
230 VAC input 1 mA max.
115 VAC input 16 A typ.
230 VAC input 32 A typ.
1.3 A
31.2 W
1.56 A
21.6 to 28 V (with V.ADJ)
100 to 240 VAC input 190 mVp-p max.
*1 at 20 MHz of bandwidth
0.5% max.
1.5% max.
115 to 230 VAC input 0.05%/°C max.
115 VAC input *1 1000 ms max.
230 VAC input *1 1000 ms max.
115 VAC input *1 30 ms typ.
230 VAC input *1 140 ms typ.
Yes, automatic reset
Yes, 130% or higher of rated output voltage, power shut off (shut off the input voltage and turn on
the input again)
Yes (For up to two Power Supplies, external diodes are required.)
Yes (For up to two Power Supplies), Refer to Parallel Operation on page 21 for details.
Yes (LED: Green)
No
3.0 kVAC for 1 min. (between all input terminals and output terminals), current cutoff 10 mA
2.0 kVAC for 1 min. (between all input terminals and PE terminals), current cutoff 10 mA
1.0 kVAC for 1 min. (between all output terminals and PE terminals), current cutoff 20 mA
100 M min. (between all output terminals and all input terminals/PE terminals) at 500 VDC
40 to 70°C (Derating is required according to the temperature. Refer to Engineering Data) (with
no condensation or icing)
40 to 85°C (with no condensation or icing)
95% RH max. (Storage humidity: 95% RH max.)
10 to 55 Hz, maximum 5G, 0.42 mm half amplitude for 2 h each in X, Y, and Z directions
2
150 m/s , 3 times each in ±X, ±Y, ±Z directions
Refer to page 12 Reference Value
10 years min.
250 g max.
No
IP20 by EN/IEC 60529
Conforms to EN 61000-3-2
Conducted Emissions Conforms to EN 61204-3 Class B, EN 55011 Class B
Radiated Emissions Conforms to EN 61204-3 Class B, EN 55011 Class B
Conforms to EN 61204-3 high severity levels
UL Listing: UL 508,ANSI/ISA 12.12.01 (For 30 W and 60 W only Class2 Output: Per UL 1310)
cUL: CSA C22.2 No107.1,
CSA C22.2 No213 (For 30 W and 60 W only Class2 Output: Per CSA C22.2 No.223)
UL UR: UL 60950-1 (Recognition) OVCII 3000 m) Pol2
cUR: CSA C22.2 No. 60950-1 OVCII ( 3000 m) Pol2
EN: EN 50178 OVCIII ( 2000 m) OVCII (2000 m and3000) Pol2,
EN 60950-1 OVCII ( 3000 m) Pol2
ATEX: EN 60079-0, EN 60079-15 Cert. DEMKO 16 ATEX 1708X (Except 30 W)
Ex II 3G Ex nA IIC T3 Gc
IECEx: IEC 50079-0, IEC60079-15 Cert. IECEx UL 16.0082X (Except 30 W)
Ex nA IIC T3 Gc
PELV (EN/IEC 60204-1) *12
EN/IEC 61558-2-16:2009+A1:2013 *12
Lloyd's register (Except 30 W)
DNV GL (Except 30 W)
Conforms to F47-0706 (200 to 240 VAC input)
30 W 60 W
24 V 24 V
87% typ.
89% typ.
*12, 265 to 300 VAC (1 second)
1.1 A typ.
0.66 A typ.
---
2.5 A
60 W
3 A
190 mVp-p max.
at 20 MHz of bandwidth
1000 ms max.
1000 ms max.
20 ms typ.
95 ms typ.
250 g max.
120 W
24 V
90% typ.
92% typ.
50/60 Hz (47 to 63 Hz)
1.2 A typ.
0.63 A typ.
0.9 min.
5 A
120 W
6 A
110 mVp-p max.
at 20 MHz of bandwidth
1000 ms max.
1000 ms max.
45 ms typ.
45 ms typ.
400 g max.