Linear PRO Access APeX-II v2.1 Quick Programming Manual

Linear PRO Access APeX-II v2.1 Gate Controller Quick Programming Guide — Basic Programming —
PRESS UP & DOWN BUTTONS FOR 1-SECOND TO ENTER PROGRAMMING
SELECT CURRENTLY OPTION READY CHOOSE OPTION
FUNCTION SET OPTION TO CHANGE OPTION STORED
UP UP
OR OR
DOWN ENTER ENTER DOWN ENTER
PRESS ENTER FOR
PRESS ENTER
PRESS UP OR DOWN ONE SECOND TO
TO STORE
TO SCROLL DISPLAY SELECT OPTION PRESS UP
OPTION
THROUGH FUNCTIONS (THE DISPLAY
OR DOWN
WILL FLASH) TO CHANGE
OPTION
PROGRAMMING PRESS ENTER TO PRESS UP, DOWN
DISPLAY CURRENTLY OR ENTER SELECT
KEYSTROKES
SET OPTION NEXT FUNCTION
APEX FUNCTION
DISPLAY INDICATIONS
LEFT OR RIGHT LOW POWER
"RL"
"LP"
HAND OPERATION MODE
SINGLE OR POWER
"PM" "FS"
DUAL GATE FAILURE MODE
AUTO CLOSE SOFT START/STOP
"AC" "SS"
TIMER DURATION
RUN ALARM RESET CYCLE
"RP" "CT"
PRE-START ALARM COUNT
MAXIMUM OPEN MAINTENANCE ALERT
"OC" "MA"
CURRENT TRIGGER
MAXIMUM CLOSE OPEN/RESET
"CC"
"OR"
CURRENT INPUT
ADVANCED ANTI
"AD" "TG"
PROGRAMMING TAILGATE
MAXIMUM MID-TRAVEL
"RT" "MT"
RUN TIMER STOP POSITION
SINGLE BUTTON ANTI-TAILGATE
"SB" "AT"
INPUT SETUP ENABLE
STAGGER RADIO
"SM" "RA"
MODE ENABLE
STAGGER LEARN
"ST" "TL"
TIME TRANSMITTERS
AUXILIARY DELETE
"AR"
"TD"
RELAY MODE TRANSMITTERS
REVERSE LEARN MGT
"RD" "ML"
DELAY TIME TRANSMITTERS
BRAKE ERASE MGT
"BD" "MD"
DELAY TIME TRANSMITTERS
CONSTANT MOTOR TYPE
"CP"
"MO"
PRESSURE MODE SELECTION
SHADOW LOOP RESET TO
"SP" "CL"
OPEN PREVENTION FACTORY DEFAULTS
OPEN OBSTRUCTION OBSTRUCTION
"OO" "OT"
INPUT ACTIVE DETECTION TYPE, b1, b2
MGT MONITIRING REMOTE CLOSE
"MM" "RC"
FUNCTION OBSTRUCTION ACTIVE
CLOSE OBSTRUCTION REMOTE OPEN
"CO" "RO"
INPUT ACTIVE OBSTRUCTION ACTIVE
FUNCTION
OPTIONS
PRESS UP OR
"RL"
DOWN TO CYCLE
SELECT
THROUGH OPTIONS
FUNCTION
PRESS ENTER TO
SELECT AN OPTION
ENTER
NOT FOR
*** FOR LRA ARM INSTALLATIONS ONLY: ***
OR
BARRIER GATES
FOR LRA PULL-TO-OPEN INSTALLATIONS (GATE SWINGS IN TO
OPEN) LEAVE THE CONTROLLER SET FOR RIGHT HAND OPERATION
UP
LEFT HAND
FOR LRA PUSH-TO-OPEN INSTALLATIONS (GATE SWINGS OUT TO
OR
OPEN) SET THE CONTROLLER FOR LEFT HAND OPERATION
RIGHT HAND
DOWN
FUNCTION OPTIONS
RUN ALARM OFF
"RP"
PRE-START ALARM OFF
RUN ALARM ON
PRESS UP OR
PRE-START ALARM OFF
DOWN TO CYCLE
THROUGH OPTIONS
RUN ALARM ON
PRESS ENTER TO
PRE-START ALARM ON FOR 1 - 9 SECONDS
SELECT AN OPTION
RUN ALARM
PRE-START ALARM
FUNCTION OPTIONS
"OT"
FOR NON-CONTACT SENSOR
FOR CONTACT SENSOR
OBSTRUCTION
DETECTION TYPE
FUNCTION OPTIONS
REMOTE OPERATOR
"RO" OBSTRUCTION
INPUT INACTIVE
REMOTE OPERATOR
OBSTRUCTION
MUST BE ON FOR INPUT ACTIVE
SLIDE GATES
REMOTE OPEN
OBSTRUCTION ACTIVE
FUNCTION
RIGHT HAND INSTALLATION
"PM"
(OPERATOR ON RIGHT OF GATE
WHEN VIEWED FROM INSIDE)
LEFT HAND INSTALLATION
(OPERATOR ON LEFT SIDE OF
GATE WHEN VIEWED FROM INSIDE)
PRESS UP OR
DOWN TO CYCLE
THROUGH OPTIONS
SINGLE GATE
PRESS ENTER TO
SELECT AN OPTION
DUAL GATE
FUNCTION
"OC"
NOT FOR
BARRIER GATES
NOT FOR
MAX OPEN
BARRIER GATES CURRENT
FUNCTION
"OO"
MUST BE ON FOR
SLIDE GATES
OPEN OBSTRUCTION
INPUT ACTIVE
FUNCTION
"RC"
REMOTE CLOSE
OBSTRUCTION ACTIVE
OPTIONS FUNCTION
SINGLE GATE INSTALLATION
"AC"
PRESS UP OR
DUAL GATE INSTALLATION
DOWN TO CYCLE
THROUGH OPTIONS
PRESS ENTER TO
SELECT AN OPTION
AUTO CLOSE
TIMER
FUNCTION
OPTIONS
"CC"
PRESS AND HOLD THE ENTER BUTTON
MAXIMUM LOAD RANGE NUMBER WILL BE
DISPLAYED. ADJUST TO THE PROPER VALUE
MAX CLOSE
ENTER
PRESS ENTER TO STORE THE VALUE
CURRENT
OPTIONS
FUNCTION
OPEN OBSTRUCTION
"CO"
INPUT INACTIVE
OPEN OBSTRUCTION
MUST BE ON FOR
INPUT ACTIVE
SINGLE GATES
CLOSE OBSTRUCTION
INPUT ACTIVE
OPTIONS
REMOTE CLOSE
OBSTRUCTION INACTIVE
REMOTE CLOSE
OBSTRUCTION ACTIVE
OPTIONS
AUTO CLOSE TIMER DISABLED
SET TIMER VALUE
1 TO 59 SECONDS
SET TIMER VALUE
1 TO 9 MINUTES
OPTIONS
PRESS AND HOLD THE ENTER BUTTON
MAXIMUM LOAD RANGE NUMBER WILL BE
DISPLAYED. ADJUST TO THE PROPER VALUE
ENTER PRESS ENTER TO STORE THE VALUE
OPTIONS
CLOSE OBSTRUCTION
INPUT INACTIVE ONLY IF
SECOND GATE ACTIVE
CLOSE OBSTRUCTION
INPUT ACTIVE