Table of Contents
Advertisement
EN 24
6.
TPM9.1E LA
6. Alignments
Index of this chapter:
6.1 General Alignment Conditions
6.2 Hardware Alignments
6.3 Software Alignments
6.4 Option Settings
6.5 Reset of Repaired SSB
6.1
General Alignment Conditions
Perform all electrical adjustments under the following
conditions:
•
Power supply voltage: 90 - 264 V
•
Connect the set to the mains via an isolation transformer
with low internal resistance.
•
Allow the set to warm up for approximately 15 minutes.
•
Measure voltages and waveforms in relation to correct
ground (e.g. measure audio signals in relation to
AUDIO_GND).
Caution: It is not allowed to use heat sinks as ground.
•
Test probe: R
> 10 M, C
i
•
Use an isolated trimmer/screwdriver to perform
alignments.
6.2
Hardware Alignments
Not applicable.
6.3
Software Alignments
Put the set in SAM mode (see Chapter
Codes, and Fault
Finding). The SAM menu will now appear on
the screen. Select RGB Align and go to one of the sub menus.
The alignments are explained below.
The following items can be aligned:
•
White point
To store the data:
•
Press OK on the RC before the cursor is moved to the
left.
•
Select "Store" and press OK on the RC.
•
Switch the set to stand-by mode.
For the next alignments, supply the following test signals via a
video generator to the RF input:
•
EU/AP-PAL models: a PAL B/G TV-signal with a signal
strength of at least 1 mV and a frequency of 475.25 MHz
•
US/AP-NTSC models: an NTSC M/N TV-signal with a
signal strength of at least 1 mV and a frequency of
61.25 MHz (channel 3).
•
LATAM models: an NTSC M TV-signal with a signal
strength of at least 1 mV and a frequency of
61.25 MHz (channel 3).
6.3.1
RGB Alignment
Before alignment, set the picture as follows:
Picture Setting
Dynamic backlight
Dynamic Contrast
Color Enhancement
Picture Format
Light Sensor
Brightness
Color
Contrast
White Tone Alignment:
•
Activate SAM.
•
Select "RGB Align." and choose a color temperature.
•
Use a 100% white screen as input signal and set the
following values:
–
"Red BL Offset" and "Green BL Offset" to "7" (if
present).
–
All "White point" values initial to "128".
2012-Apr-27
Alignments
, 50/ 60 3 Hz.
AC
< 20 pF.
i
5. Service Modes, Error
Off
Off
Off
Unscaled
Off
50
0
100
In case you have a colour analyser:
•
Measure with a calibrated (phosphor- independent) color
analyser (e.g. Minolta CA-210) in the centre of the screen.
Consequently, the measurement needs to be done in a
dark environment.
•
Adjust the correct x,y coordinates (while holding one of the
White point registers R, G or B on max. value) by means of
decreasing the value of one or two other white points to the
correct x, y coordinates (see Table
values). Tolerance: dx: 0.010, dy: 0.010.
•
Repeat this step for the other colour Temperatures that
need to be aligned.
•
When finished return to the SAM root menu and press
STANDBY on the RC to store the aligned values to the
NVM.
Table 6-1 White D alignment values
Value
Cool (11000 K)
x
0.276
y
0.282
If you do not have a colour analyser, you can use the default
values. This is the next best solution. The default values are
average values coming from production (statistics).
6.3.2
Display Adjustment
You can use the default values. The default values are average
values coming from production.
•
Enter SAM mode.
•
Select a colour temperature (e.g. COOL, NORMAL, or
WARM).
•
Set the RED, GREEN and BLUE default values according
to the values in
•
When finished press OK on the RC, then press STORE to
store the aligned values to the NVM.
•
Restore the initial picture settings after the alignments.
Table 6-2 White tone default settings
Picture mode
Normal (9000K)
Cool (11000K)
Warm (6500K)
This group setting of colour temperature will be applied
automatically to the TV / VGA / HDMI / AV sources.
back to
div. table
6-1 White D alignment
Normal (9000 K)
Warm (6500 K)
0.287
0.296
Table
6-2.
Colour temperature
Screen size
Red
Green
32PFL3007
128
116
32PFL3017
128
116
37PFL3007
128
122
42PFL3007
128
122
47PFL3007
128
128
32PFL3007
128
124
32PFL3017
128
124
37PFL3007
113
112
42PFL3007
110
114
47PFL3007
114
116
32PFL3007
128
103
32PFL3017
128
104
37PFL3007
128
110
42PFL3007
128
114
47PFL3007
128
120
0.313
0.329
Blue
101
101
124
124
104
124
123
128
128
128
59
59
80
78
66
Hide quick links:
Advertisement
Table of Contents
