Stepwise Start-Up; How To Exit Csm - Philips 32PFL3007H/12 Service Manual

• 1.3 Installation date Indicates the date of the first
installation of the TV. This date is acquired via time
extraction.
• 1.4 Option Code 1 Gives the option codes of option group
1 as set in SAM.
• 1.5 Option Code 2 Gives the option codes of option group
2 as set in SAM.
• 1.6 SSB Gives an identification of the SSB as stored in
NVM. Note that if an NVM is replaced or is initialized after
corruption, this identification number has to be re-written to
NVM. This identification number is the 12NC number of the
SSB.
• 1.7 Display 12NC NVM read/write.
• 1.8 PSU 12NC NVM read/write.
• 2.1 Current Main SW Displays the built-in main software
version. In case of field problems related to software,
software can be upgraded. As this software is consumer
upgradeable, it will also be published on the internet.
• 2.2 Standby SW Displays the built-in stand-by processor
software version. Upgrading this software will be possible
via USB.
• 2.3 Panel Code Displays the Display Code number.
• 2.4 NVM version Detects and displays NVM version.
• 2.5 Error Codes Detects and displays errors.
5.3

Stepwise Start-up

Standby Soft Mode
Command Received,
previously in Standby
Soft Mode (Power tact
switch)
TV Wakeup
commands
Received
(TV Wakeup
keys)
Power On
Service Modes, Error Codes, and Fault Finding
Digital
background
tasks started
Standby
commands
Received (RC
Standby key)
Standby Soft Mode
Command Received,
previously in Standby
Soft Mode (Power
TV Wakeup
tact switch)
commands
Received
(TV Wakeup
keys)
Switch On, previously
in Power On Mode
(Power tact switch)
Standby Soft Mode
Command Received,
(Power tact switch)
Figure 5-1 Stepwise Start-up
• 3.1 Signal Quality Analog/digital signal strength.
• 3.2 Child lock Not active / active. This is a combined item
for locks. If any lock (channel lock, parental lock) is active,
it is indicated as "active".
• 3.3 HDCP keys Indicates the validity of the HDMI keys (or
HDCP keys). In case these keys are not valid and the
customer wants to make use of the HDMI functionality, the
SSB has to be replaced.
• 3.4 e-UM version Version of the available built in
electronic manual.
How to Navigate
By means of the "CURSOR-DOWN/UP" knob (or the scroll
wheel) on the RC-transmitter, can be navigated through the
menus.

How to Exit CSM

To exit CSM, use one of the following methods.
• Press the MENU/HOME button on the remote control
transmitter.
• Press the POWER button on the remote control
transmitter.
• Press the POWER button on the television set.
Standby
Digital
background
tasks completed
Swith On,
Semi-
previously in
Standby
Standby/Semi-
Standby (Mains
Power Plug)
Standby
Soft Mode
Command
Switch Off (Mains
Received
Power Plug)
(Power tact
switch)
Standby
Swith On,
Soft Mode
previously in
Standby Soft Mode
(Mains Power Plug)
Switch Off (Mains
Power Plug)
back to
div. table
TPM9.1E LA 5.
Switch
Off(Mains
Power Plug)
Switch Off
(Mains Power
Plug)
Power Off
Switch On,previously in
TV Operation Mode
(Mains Power Plug)
EN 19
19080_206_110323.eps
120224
2012-Apr-27