Related Manuals for Omegasonics 7850TT
Summary of Contents for Omegasonics 7850TT
- Page 1 Omegasonics Ultrasonic Cleaning Equipment Operation & Instruction Manual OMEGASONICS Table Top Unit 2017 and After Model 7850TT / 7950TT Read all instructions thoroughly before operating this equipment...
-
Page 2: Table Of Contents
TABLE OF CONTENTS Introduction…………………………………………………………………………..………………………..3 Warnings………………………………………………………………………………………………………...4 Getting to Know Your Unit………………………………………………………………………………5 Cleaning Solution Limitations………………………………………………………………………….9 Set Up……………………………………………………………………………………………………………10 Cleaning………………………………………………………………………………………………………..10 Specific Cleaning Procedures…………………………………………………………………………11 Equipment Maintenance……………………………………………………………………………….12 Service Life of Transducer Tank……………………………………………………………………..14 Trouble Shooting…………………………………………………………………………………………..15 Omegasonics Cleaning Agents……………………………………………………………………….17 Limited Warranty…………………………………………………………………………………………..18... -
Page 3: Introduction
As a result, ultrasonic cleaning is one of the most highly effective and efficient methods you can use for cleaning a wide array of items. Omegasonics provides a complete line of quality ultrasonic cleaning washers that have been developed for industries that have historically used technology that is quickly becoming outdated. -
Page 4: Warnings
These chemicals will cause permanent damage to the stainless steel welds. Use only biodegradable cleaning agents. Never use solvents or flammable cleaning solvents without approval from Omegasonics. Any chemistry with a flash point below 82˚C should never be used with an ultrasonic cleaner. ... -
Page 5: Getting To Know Your Unit
GETTING TO KNOW YOUR UNIT Delivered Equipment Ultrasonic cleaning unit Lid Electrical Power Cable Tube socket with tube clamp Operating Instruction Manual Basket Front Control Panel Ultrasound LED Display/ button Cleaning Period Turning Knob Temperature Turning Knob Temperature LED Display... - Page 6 position (or whichever increment of time you desire). This will start the heating process. Even though you are selecting a time (or continuous) option, the ultrasound will NOT be activated, and the timing will not start, until the is pressed. ...
-
Page 7: Cleaning Solution Limitations
The limitations of use also apply to the standard cleaners and disinfectants if these contain the above mentioned compounds. For a list of Soaps offered by Omegasonics, please refer to page 17. -
Page 8: Set Up
Alternatively, turn the knob back into “Off” position. In order to avoid unintended permanent operation, the Omegasonics units are equipped with a safety switch-off automatically. The unit switches off completely after 8 hours of permanent operation. If you wish to continue the operation, start the unit... -
Page 9: Specific Cleaning Procedures
SPECIFIC CLEANING PROCEDURES Carburetors In the ultrasonic bath, preheat 1 part OmegaSupreme with 10 parts clean water to a temperature of 66˚C. Remove float bowls and jets from the carburetor to be cleaned. Hoses and gaskets do not need to be removed. ... - Page 10 Pistons In the ultrasonic bath, preheat 1 part OmegaSupreme with 10 parts clean water to a temperature of 68˚C. Place the piston, face down, in the basket and submerge the basket into the bath. Presoak for 10 minutes. Once this is done, activate the ultrasound for 15 minutes. ...
- Page 11 Firearms In the ultrasonic bath, preheat 1 part OmegaBlue with 32 parts clean water to a temperature of 46˚C. Disassemble the firearm into its major components. If it is equipped with a scope, it can be left attached. ...
-
Page 12: Equipment Maintenance
Skim off oil and grease residue periodically, if necessary. Cleaning agents should be changed periodically depending on usage. The Omegasonics unit is maintenance-free. Check the casing and the main electrical cable for damage regularly in order to prevent electrical accidents. Draining Tank ... - Page 13 Always thoroughly inspect drain areas for leaks. When discharging bath and waste, follow all environmental and regulatory requirements. A reputable and licensed waste transportation firm should perform removal of all waste materials. Omegasonics is not liable for improper handling of waste materials.
-
Page 14: Service Life Of Transducer Tank
The changes on the surfaces that occur after a certain operating period are visible first as grey areas and later on as abrasions, the so-called cavitation erosion. Omegasonics already uses highly cavitation-resistant special steel. To prolong the service life of your ultrasonic unit even more we recommend observing the following instructions: •... -
Page 15: Trouble Shooting
Trouble Shooting Fault Possible Cause Remedy Main cable not plugged in Plug in main cable No operating functions; all LED displays dark Socket dead Check socket and fuse Main cable damaged or interrupted Replace main cable Return unit to supplier or Faulty electronics manufacturer Turning knob for ultrasound in... - Page 16 Trouble Shooting Fault Possible cause Remedy switch on turning knob temperature turning knob temperature in Unit does not heat up; LED display position „0“ temperature dark Unit is switched off Switch on unit at on/off key Return unit to supplier or Faulty electronics manufacture No heating;...
- Page 17 CLEANING AGENTS - OMEGASONICS Omegasonics carries a full line of cleaning agents. Each cleaning agent has a unique cleaning specialty and use. Some of the products are as follows. OmegaSupreme – Heavy-duty degreaser removes carbon, oil, dirt, grease and dirt from a variety of metals.
-
Page 18: Limited Warranty
LIMITED WARRANTY Omegasonics warrants the 7850TT and 7950TT ultrasonic cleaner for a period of two (2) years from the date of delivery, when used in accordance with the manufacturer’s instructions. During the warranty period, Omegasonics will repair or replace free of charge at an authorized repair service center all parts that are defective because of material or workmanship.