Regular Maintenance; Thermal Cover Care; Everpure Ozone Care; Plumbing Care - PDC spas Luxury Series Owner's Manual

Regular Maintenance
Thermal Cover Care
Always use the locking thermal cover when not in use to reduce heat‐up me, opera ng costs and keep unwanted out. To
prolong the life of the cover, handle it with care and clean it regularly using mild soap and water. Periodic treatments with a vinyl
condi oner will help protect against deteriora on caused by UV rays from the sun. Never allow anyone to stand or sit on the cover,
and avoid dragging it across rough surfaces. Be sure to lock all straps when not in use for safety and to prevent wind damage. Keep
cover open at least 15 minutes a er adding chemicals.
EverPure™ Ozone Care
The ozone hose and check valve connec on between the ozone generator and ozone injector should be inspected or replaced, if
necessary, annually. The air quality pulled into the generator may cause rapid wear on the hose and check valve. The EverLite™
will light green when the ozone generator is opera ng (during the filtra on cycle) indica ng the EverPure™ system is indeed
sani zing the water.
Plumbing Care
Hot tubs are plumbed with plas c jets, pipes and fi ngs which are glued together. These plas c parts and their many glue
joints are subjected to harsh treatment with years of opera on, subjected to many hot‐cold cycles and the high pressure
generated by the powerful jet pump stressing pipes and joints. Although the factory has a rigorous tes ng procedure, even
transporta on from the factory to you can cause vibra on and possible loosening of the joints.
Should a leak occur, remove that appropriate sec on of cabinet wall exposing the leaking area. Drain the hot tub to below the leak
and contact a qualified technician for repair.
Filter Cartridge Care
Hot tub water filtra on begins as soon as the flow is steady through the pump. As the filter cartridge removes dirt from the water,
the accumulated debris will cause a resistance to flow. When this is no ced, along with cloudy water, clean or replace the fi lter
element as noted below. This generally occurs monthly depending upon use and water care.
PowerFlo™ System: (Luxury and Premium Series)
1. Shut off power at the main or sub panel.
2. Open the small, black bleeder valve on top of the filter cover slightly to release pressure. (Be sure to re‐close the valve snugly
before reac va ng the spa. Do not over ghten, there is a risk of cracking.)
3. Remove the black lock ring. Li the dome lid and remove the filter element. Clean any debris from the filter housing. Soak the
filter element in a non‐sudsing filter cleansing solu on.
4. Rinse the filter element with a garden hose or pressure hose, and replace in the filter housing. (It is recommended to have an
extra filter cartridge on hand so that a clean element will always be available while the soiled element is being cleaned. This will
minimize down me of the spa during the cleaning procedure.) When replacing the element into the housing, be sure that the o‐ring
is in place and clear to assure a snug fit of the filter dome lid to prevent leakage. Hand ghten the lock ring un l snug and locking tab
engages. Do not over ghten, there is a risk of cracking. Re‐check bleeder valve to be sure it is closed.
Pris ne™ System: (Lifestyle Series)
1. Shut off power at the main or sub panel.
2. Remove the filter housing top by using the raised por ons of the filter top and turning it counter clockwise. A er top
stops turning, li up to remove top from filter.
3. Li the skimmer basket out of the filter canister.
4. Remove the filter from the canister.
5. Replace with clean filter ( Review above for cleaning recommenda ons.)
6. Place skimmer basket back in filter canister.
7. Place filter top onto filter canister and turn clockwise un l top stops.
Hot Tub Acrylic Surface Care
To preserve the sheen of the acrylic surface, clean and sani ze with clean water to remove any par cles and use rubbing alcohol
or a non‐abrasive, non‐sudsing cleaner to wipe clean. Use a so , lint free cloth and never use an aggressive solvent such as a
lacquer thinner or acetone which will cause damage to the acrylic.
47