1. Sicherheitshinweise zum Betrieb des Gerätes Dieses Gerät erfüllt die EU-Bestimmungen 2004/108/EG (elektromagnetische Kompatibilität) und 2006/95/EG (Niederspannung) entsprechend der Festlegung im Nachtrag 2004/22/EG (CE- Zeichen). Zur Betriebssicherheit des Gerätes und zur Vermeidung von schweren Verletzungen durch Strom- oder Spannungsüberschläge bzw. Kurzschlüsse sind nachfolgend...
Page 3
® Das Labornetzgerät PeakTech 6145 verfügt über 2 Ausgänge mit einer kontinuierlich veränderbaren Ausgangsspannung von 0 ... 30 V bzw. einem Ausgangsstrom von 0 ... 5 A. Ein weiterer Ausgang liefert eine Festspannung von 5 V bzw. 3 A. Die beiden kontinuierlich veränderbaren Ausgänge können wahlweise in Reihe oder parallel geschaltet werden.
2. Technische Daten 115/230 V, 50/60 Hz Wechselspannung (umschaltbar) 10% Eingangsspannung Ausgangsspannung 2 x 0 ... 30 V DC (kontinuierlich veränderbar) Stromausgang 2 x 0 ... 5 A DC (kontinuierlich veränderbar) Festwertausgang 5 V / 3 A DC Stabilität zwei kontinuierlich veränderbare Spannungsausgänge: 1 x 10 + 3 mV...
3. Betrieb des Gerätes 3.1. Anzeigen und Bedienelemente des Gerätes 01. Ampere-Anzeige für Slave-Netzteil bzw. Anzeige bei Parallelbetrieb (LED leuchtet bei geschaltetem Stromausgang im Slave-Betrieb bzw. bei Parallelbetrieb). 02. Stromregler für Slave-Betrieb (Einsteller für Strombegrenzer-Schutzschaltung). 03. Spannungsanzeige für Slave-Betrieb (LED leuchtet bei geschaltetem Spannungsausgang bei Slave-Betrieb).
Page 6
3.2. Betriebsarten Output-Taste (24.) drücken, um die Ausgänge zu aktivieren bzw. zu deaktivieren. So ist es auch möglich angeschlossene Testschaltungen schnell spannungsfrei zu schalten. 3.2.1. Einstellung des Ausgangssignals bei individuellem Betrieb (Einzelbetrieb von Master und Slave). Funktionswahlschalter (7.) und (9.) falls gedrückt auslösen. Zur Einstellung der gewünschten Ausgangsspannung (0 ...
1. Safety Precautions This product complies with the requirements of the following European Community Directives: 2004/108/EC (Electromagnetic Compatibility) and 2006/95/EC (Low Voltage) as amended by 2004/22/EC (CE-Marking). To ensure safe operation of the equipment and eliminate the danger of serious injury due to short- circuits (arcing), the following safety precautions must be observed.
Page 9
® The model PeakTech 6145 regulated power supply has two ways adjustable output. The two adjustable outputs can also be selected for constant voltage or constant currant, designed in high stability and performance circuit. In constant voltage state, the output voltage can be arbitrarily from 0 V on the nominal range;...
2. Technical Data 115/230 V AC, 50/60 Hz 10% (switchable) Input voltage: Output voltage: 2 x 0 ... 30 V DC (adjustable) Output current: 2 x 0 ... 5 A DC (adjustable) Source regulation: Two adjustable outputs: 1 x 10 + 3 mV 2 x 10 + 3 mA...
3. Operation 3.1. Controls and description 01. Slave constant-current indicator or two-ways parallel state indication: the LED illuminates when the slave output is in current-regulated state or the two adjustable outputs is in parallel. 02. Slave constant current adjustment: adjusting slave output current value (adjusting the current-limit protection point).
Page 12
3.2. Operating method Press output-button (24.) to enable or disable the outputs. If is also possible to turn off the outputs easily and the connected test circuits are quickly without tension. 3.2.1. Independence use of two adjustable output. Set (7.) and (9.) switch to spring out position. When the adjustable output is used as CV output, first should rotate clockwise the CC adjustment (2.) and (17.) to maximum, then turn on power switch (13.), adjust CV adjustment (4.) and (14.) till output voltage reach required voltage value, at this time, the...
Page 13
3.2.3. Parallel using of the two adjustable outputs. Press in switch (7.) as well as switch (9.), at this time, the two output are in parallel, adjust voltage adjustment (14.) of master output, the voltage of two ways keep same, and slave output CC indicator (1.) lights on.