Page 2
Deutsch Magyar English Česky Français Slovensko Italiano Polska Nederlands Româneşte Español Türkçe Português Русский Slovensky ÅëëÞíéêÜ ÅëëÞíéêÜ ÅëëÞíéêÜ ÅëëÞíéêÜ Dansk Hrvatski Norsk Srpski Svenska Български Suomi...
Operating Instructions English Contents Warning! Environmental protection Prior to initial operation it is mandatory to read the operating instructions and the Unit illustration notes on safety no. 5.951-949! Operating controls Inform retailer immediately of any transportation damage. Reference to operating instructions Commissioning Environmental protection...
English Operating Instructions Unit illustration Operating controls 1 Fuel tank inlet 18 Water connection with strainer 2 Handle 19 High-pressure connection 3 Instrument panel 20 Handgun with high-pressure hose 4 Window with the 22 Electric power cord maintenance/fault display 23 Unit switch 5 Cover latch 24 Temperature regulator 6 Compartment für accessories...
Operating Instructions English Reference to operating ! For other water hardnesses request instructions services of a Kärcher service station and have it adapted to local conditions. All of the item numbers described below in the operating instructions are referenced in Filling with fuel the illustration of the unit.
Page 10
English Operating Instructions Installing the handgun (units Drawing in water from tank without hose reel) When you suction water out of an open ! Connect steel pipe (item 15) with container you should handgun (item 20) ! Insert high-pressure nozzle in union nut ! remove water connection at pump head.
Operating Instructions English Setting cleaning temperature — If direction of rotation is correct, powerful jet of air will be felt at exhaust-gas ! Set the remperature regulator (item 24) opening of burner. to the required temperature — If the direction of rotation is wrong: Change the poles at the unit 30°C to 90°C plug.
English Operating Instructions Measuring out cleaning agents Recommended nozzles, available as — Use cleaning agents sparingly to protect accessories the environment — For stubborn dirt — The cleaning agent must be appropriate 0°full jet nozzle for the surface to be cleaned. —...
Operating Instructions English Operation with hot water ! Set operating pressure to minimum value. See Fig. 10 Warning! ! Set the temperature regulator (item 24) Danger of scalding to min. 100°C ! Set the remperature regulator (item 24) to the required temperature Danger: Steam! Danger of scalding! We recommend the following cleaning...
English Operating Instructions ! Reel up the high-pressure hose and Flushing unit with anti-freeze electric cables and attach them to ! Fill the float tank with a commercially fastenings available antifreezing compound ! Swith the unit on (without the burner) Note! until it is thoroughly purged Take care not to kink high-pressure hose...
Operating Instructions English Maintenance intervals Display Once a week — Clean strainer in water connection — Clean the fine filter Necessary maintenance work — Check oil level ! Visual inspection Immediately consult the Kärcher service ! Check that the high-pressure station when oil turns milky! connections do not leak ! Clean the fuel tank and the filter...
English Operating Instructions Clean strainer in water Change oil connection Fig. 11 Fig. 16 ! Remove strainer ! Provide a collecting container for ! Clean in water and re-insert approx. 1 litres of oil ! Unscrew drain plug Clean the fine filter Dispose of used oil ecologically or hand it Fig.
Page 17
Operating Instructions English Display Ready for working indicator lamp (item 29) goes out — Motor overloaded/overheated Troubleshooting ! Set selector switch to "0" and allow ! Replace the reed switch for the low engine to cool off for at least 5 min. water protection * ! Have unit checked by After-Sales ! Clean the low water protection *...
Page 18
English Operating Instructions ! Fill up cleaning-agent tank if empty. Burner not ignited ! Check connections and lines — Fuel tank empty ! Fill up — Pressure set to MIN ! Set pressure to MAX — Lack of water ! Check water connection, check supply, —...
Operating Instructions English Warranty The overflow valve is set at the factory and The warranty terms and conditions issued lead-sealed. Adjustment can only be made by our responsible sales company apply in by After-Sales Service. every country. Within the warranty period, any faults in the unit will be rectified free of Safety valve charge provided that the problem was...
English Operating Instructions EC conformity declaration Measured sound power level: We hereby declare that the machine HDS 995 89 dB(A) specified below as the marketed desigh, HDS 1295 88 dB(A) the machine specified below complies with the relevant fundamental safety and health Guaranteed sound power level: requirements of the EC directives listed HDS 995...