Troubleshooting by the oper- Contents Accessories and Spare Parts ator with plain text messag- DANGER es on the display..Contents ....EN To avoid risks, all repairs and replacement Troubleshooting with coded General notes .
Proper use Safety instructions Safety information concerning the driving operation The sweeper is intended for cleaning floor Safety instructions concerning the Danger surfaces for commercial use and e.g. for operation Risk of injury! the following fields of application: – The machine with working equipment Danger of tipping if gradient is too high.
Function The sweeper operates using the overthrow principle. – The side brushes (3) clean the corners and edges of the surface, moving dirt and debris into the path of the roller brush. – The rotating roller brush (4) moves the dirt and debris directly into the waste container (5).
Operating and Functional Elements 1 Operating field (KM 105/100(110) R Bp Pack: already Control elements on the control panel 2 Steering wheel installed) 1 Main switch 3 Cover on the left (KM 105/100(110) R Bp: not included in Position 0: Appliance is decommis- 4 Pedal for raising/lowering bulk waste delivery) sioned...
6 Display sweeping programme Note: In this menu item the authorisa- Program selection switch "HEAVY" tions for the yellow intelligent key are Note – for heavily soiled and uneven floors enabled. The functions are only activated with the 7 Display ...
Waste container (low emptying system) Both waste containers are equipped with a safety installation that switches off the run- ning device when it is opened and issues a warning message on the display. Waste container (high emptying system) The high emptying system is equipped with a safety installation that blocks the sweeping operation during the emptying procedure.
NOTICE Check and correct the fluid level of the Notes regarding the battery When removing the battery, make sure that battery (only for low-maintenance Safety notes regarding the batteries the negative pole lead is disconnected first. batteries) Please observe the following warning notes Check that the battery pole and pole termi- Warning when handling batteries:...
Note During a standstill of the machine: Reverse drive The progress of the charging process is Check the drive pedal for ease of move- DANGER shown via a bargraph (5 bars) on the display. ment in order to guarantee functional Risk of injury! At the beginning of the charging process reliability or timely detect a jamming of...
Sweeping with sweep roller Sweeping damp or wet floors With appliances with high emptying system For cleaning with the roller brush 3 different To protect the filter from moisture: sweeping programmes are available, they Switch the suction blower off using the The high emptying system of the appliance are shown by 2 arrows on the display.
Note: Function reacts with a delay. Cleaning the inside of the machine Storage Note: The waste container can only be Danger CAUTION completely lowered after it has been Risk of injury! Wear dust mask and protec- Risk of personal injury or damage! tipped inwards into its initial position.
Dismantling the drive Maintenance Works Contact the customer service for the re- General notes on safety moval of the drive. Danger Check the function of the seat contact Risk of injury! While working around the lift/ switch tilt emptying mechanism, raise the waste ...
Page 16
Front sealing strip Loosen screws. Adjusting the sealing strip: Fold the lid up and secure it by means Loosen the nuts by approx. 2 rotations, of the support. do not completely unscrew them. Take out the dust filter. ...
Sit on the driver seat, the seat contact switch gets activated. Set main switch to “I/ON”. Insert approved key (intelligent key) Plug in battery plug (KM 105/100 R Bp; KM 105/110 R Bp) Close left cover. Properly insert the waste container (low emptying system) or completely tip it inwards and...
Troubleshooting by the operator with plain text messages on the display Note: If the display messages shown remain despite the corrective measures described, contact service! Display Meaning and consequence Corrective measures Invalid KiK! The identification of the inserted key is unknown. ...
Display Meaning and consequence Corrective measures SBroompos.not ok Is displayed when the optionally available sickle brush Confirm the message with the OK key (delete). cannot move to the factory-set end position. Turn the programme selector switch to position –...
Specifications KM 105/100 R Bp KM 105/100 R Bp Pack KM 105/110 R Bp KM 105/110 R Bp Pack Machine data Length x width x height 1800 x 1250 x 1450 1800 x 1250 x 1450 Net weight (transport weight)
Page 21
KM 105/100 R Bp KM 105/100 R Bp Pack KM 105/110 R Bp KM 105/110 R Bp Pack Battery Type 24V 4 PzS 240 I Capacity Charging time for fully discharged battery 10...15 Operating time after frequent charging ca. 2,5...
EC Declaration of Conformity Accessories We hereby declare that the machine de- Side brushes, standard 6.966-063.0 scribed below complies with the relevant For cleaning of indoor and outdoor areas. basic safety and health requirements of the EU Directives, both in its basic design and Hard side-brushes 6.906-705.0 construction as well as in the version put...
Need help?
Do you have a question about the KM 105/100 R Bp and is the answer not in the manual?
Questions and answers