Table of Contents
Advertisement
Installation Manual I Operation
4.5 Daily Preparation for Use - Connectionless Model
Preparing the Evolution Connection-Less model for use each
day requires very little time and effort. Simply verify that the
steamer is clean, the drain valve is in the closed position and the
cooking chamber is filled with approximately 2½ Gallons of tap
water. Close the door and push the ON/OFF key on the keypad.
The water level will need to be monitored and filled as required.
Do not use the low water warning lamp as the indicator to
check the water level as this can damage the steamer over time.
PREHEATING
1.
Depress the ON/OFF Key to turn on the steamer. The
display will indicate PrE.
2.
Once the steamer is preheated and ready to cook, the
display will indicate COO (Cook Mode) or HLd (Hold Mode).
3.
Depress the DISP TEMP button to display the current
cooking chamber temperature. MAX temperature at sea
level in 212°F
COOKING
1.
Depress the COOK/HOLD button to select the Cook Mode
(COO).
2.
Open the door and place food into the cooking chamber.
Shut the door.
Cooking begins immediately.
3.
Timer — Depress the TIMER button and depress the
ARROW keys until the desired time is displayed. The
timer starts automatically. At the end of the timed cycle, a
beeper will sound.
4.
Depress the DISP TEMP button to display the current
cooking chamber temperature.
HOLDING
In "Hold" the steamer temperature is set for 180°F
from the factory. The hold temperature can be changed to a
single value for temperatures ranging from 150° F to 190° F if
required. Contact the AccuTemp Technical Service Department
for assistance at 800.480.0415. Hold can also be used during
downtimes to save energy and water while keeping the steamer
preheated.
1.
Depress the COOK/HOLD button to select the Hold Mode
(HLd).
2.
Open the door and place food into the cooking chamber.
Shut the door.
3.
Food will be held at the preset holding temperature. The
factory default setting is set at 180° F.
4.
Depress the DISP TEMP button to display the current
cooking chamber temperature.
MP4010-1903
4.6 Power Plate Setting
The Power Plate has 3 settings:
•
•
•
Instructions to Adjust:
Tools Required
7/16" wrench or 7/16" socket wrench or adjustable wrench
Batch
1.
A la Carte
1.
2.
3.
Power Steam
1.
2.
3.
4.
ACCUTEMP EVOLUTION POWER PLATE
Batch
The Power Plate has 3 settings:
•
Batch - Factory Setting
If using a Connection-less unit, do not adjust the power
plate in the unit. It will affect the water evaporation ratio
and cause the unit to be filled more regularly
Batch - Factory Setting - Slowest Cook
A la Carte
Power Steam - Fastest Cook
Leave as received from the factory.
Remove the acorn nut and lock washer.
Remove the Power Plate and flip it so the larger size hole is
lined up over the large vent hole.
Slide the Power Plate onto the stud and install the lock
washer then the acorn nut and tighten.
Remove the acorn nut and lock washer.
Remove the power plate from the mounting stud.
Rotate plate so that the large rear vent is not covered by
the plate.
Slide onto the stud and install the lock washer then the
acorn nut and tighten.
FIGURE 19
Batch
ACCUTEMP EVOLUTION POWER PLATE
The Power Plate has 3 settings:
•
A la Carte
•
•
INSTRUCTIONS
Batch
Tools Required
7/16" wrench or 7/16" socket wrench or adjustable wre
The Power Plate has 3 settings:
Batch
•
Batch - Factory Setting
Power Steam
•
A la Carte
Leave as received from the factory.
•
Power Steam
A la Carte
INSTRUCTIONS
Remove the acorn nut and lock washer.
Tools Required
Remove the Power Plate and flip it so the larger size ho
A la Carte
7/16" wrench or 7/16" socket wrench or adjustable wrench
Slide the Power Plate onto the stud and install the lock
Batch
Power Steam
Leave as received from the factory.
Remove the acorn nut and lock washer.
ACCUTEMP EVOLU
Batch
Batch - Factory Setting
A la Carte
Power Steam
A la Carte
Power Steam
A la
Power
17
Hide quick links:
Advertisement
Table of Contents
