AccuTemp EVOLUTION Series Installation & Operator's Manual page 11

Installation Manual I Installation
3.7 Electrical Requirements and Notices
The electrical voltage requirement is listed on the data plate that is located on the lower left side panel.
All AccuTemp Evolution Electric Steamers are supplied with a power cord and plug that must be connected to the
specified receptacle, see below for reference.
Make sure the voltage is within 10% of the voltage listed on the steamer data plate.
Connection to any other voltage not identified on the data plate will cause damage to the components and is not covered under
warranty.
Grounding provides a path for electric current to reduce risk of shock.
This product is equipped with a power cord having a grounding plug. If plug is removed or hard wired, UL approval is lost.
The plug must be plugged into a receptacle that is properly installed and grounded in accordance with all National, State and
local electrical codes or in the absence of local electrical codes with the National Electric Code, ANSI/NFPA 70, or the Canadian
Code, CSA C22.2 as applicable.
Under no circumstances shall the plugs grounding prong be cut or bent to fit a receptacle other than the one specified.
Do not use any adapters.
Any in-field modification made that bypass the safety features of this appliance will result in serious injury or death. DO NOT
DIRECT WIRE THIS APPLIANCE.
Any in-field modifications made without written authorization from AccuTemp Products, Inc. will void all written and oral
warranties.
ELECTRICAL SPECIFICATIONS
CONNECTED
Model #
E62081E060
Volts AC 208
Phase 1
Amps 29
Breaker Size
30 amp
Watts (kW) 6
NEMA Plug L6-30P
CONNECTIONLESS
Model #
E62081D060
Volts AC
Phase
Amps
Breaker Size
16.23"
Watts (kW) [412mm]
NEMA Plug
16.70 R
MP4010-1903
Steamer Model "E" Specifications
E62083E100 E62083E150
208 208
3 3
28 42
30 amp 50 amp
10 15
L15-30P 15-50P
Notes:
1. Allow 3" between fryer, ranges, and other hot surfaces.
2. 5' power cord supplied with single or 3 phase.
3. For use on individual branch circuit only.
4. Do not connect to a circuit operating at more than 150V to ground.
Steamer Model "D" Specifications
5. Dimensions outside brackets are inches, in brackets are millimeters.
E62083D100 E62083D150
6. Each unit equipped with 3/4" male garden hose connector
7. Each unit equipped with 3/4" barbed drain line connector
208 208 208
8. DO NOT plumb a single drain line between the 2 units. Each
1 3 3
unit must have a separate drain line.
29 28 42
30 amp 30 amp 50 amp
6 10 15
41.15"
[1045mm]
L6-30P L15-30P 15-50P
Notes:
1. Allow 3" between fryer, ranges, and other hot surfaces.
2. 5' power cord supplied with single or 3 phase.
E6 T
6 Pan, Electric Boiler-free Convection
Countertop Steamer
E62301E070 E62401E060 E62403E110
230 240 208
1 1 3
32 25 22
50 amp 30 amp 30 amp
7 6 8
IEC 60309-2 L6-30P L15-30P
220/250V
E62401D060 E62403D110 E62403D130
240 208 240
1 3
25 22 26
30 amp 30 amp
6 8 11
L6-30P L15-30P
C E
ABLETOP ONNECTED VOLUTION
E62403E130 E64155E110
240 240
380 400 41 5
3 5
26 32 14 14 15
50 amp 20 amp
11 13 9 10 11
15-50P IEC 60309-2
E6 T C
220/380-240/415V
ABLETOP ONNECTIONLESS
6 Pan, Electric Boiler-free Convection
Connectionless Countertop Steamer
E62301D070 E64155D110
240 230
380 400 41 5
3 1 5
32 32 14 14
50 amp 50 amp 20 amp
13 7 9 10
15-50P IEC 60309-2 IEC 60309-2
220/250V 220/380-240/415V
E64803E140
440 480
3
16 17
20 amp
12 14
L16-20P
E
VOLUTION
E64803D140
440 480
3
15 16 17
20 amp
11 12 14
L16-20P
10