Download Print this page

Installing Flat Panel Screen To Wall Plate - NEC WMK-3257 Installation And Assembly Manual

Flat screen wall mount for models: aspv32, aspv40, e321, e421, e461, lcd3210, lcd3215, lcd4020, lcd4215, lcd4615, lcd4620, lcd5220, lcd5710, m40, m46, p401, p461, p521, p551, s401, s461, s521, sc40, sc46, v321, v421, v461, x431bt, x461hb, x461un, e324, ma
Hide thumbs

Advertisement

Mounting and Removing Flat Panel Screen
WARNING
• Always use an assistant or mechanical lifting equipment
to safely lift and position the fl at panel screen.
• Do not tighten screws with excessive force.
Overtightening can cause damage to mount. Tighten
screws to 40 in. • lb (4.5 N.M.) maximum torque.
• Be careful not to pinch fi ngers when pushing screen from
the bottom.
3
Tension Adjustment of Ratchet Handle:
tension in tilt brackets (B & C) by rotating ratchet
handle. NOTE: If obstruction prevents ratchet handle
from rotating, pull handle out while turning will allow
handle to reposition without tightening. Release and
turn handle to tighten or loosen.
Mounting Screen: Ratchet handle must be in the
up or down position or interference will occur while
hooking tilt brackets to wall plate (A). Slowly hook tilt
brackets (B & C) onto wall plate (A) and swing screen
down as shown in fi g. 3.1. Tilt bracket hooks must
fully engage wall plate. Using phillips screw driver or
security allen wrench (F), turn safety/security screws
on tilt brackets (B & C) clockwise till screw tip securely
contacts wall plate as shown in cross section.
Screen Adjustment: Screen can be adjusted
horizontally by loosening safety/security screws on
tilt brackets (B & C) three full turns. Adjust screen as
shown in fi gure 3.2. Tighten safety/security screws on
tilt brackets till screw tip securely contacts wall plate as
shown in cross section.
Removing Screen: To remove screen from mount,
loosen safety screws, swing screen away from mount,
and lift screen off of mount.
Adjusting the Tilt Angle of the Flat Panel
Screen
4
For preset tilt angles use
angle use ratchet handle.
INCRELOK™: The screen can be locked into a
pre-set tilt position of -5°, 0°, 5°,
locator hole to fi nd tilt position hole and tilt screen to
align holes. Tighten IncreLok™ tilt locking screws on
both tilt brackets to lock tilt as shown in detail 2.
Ratchet Handle: Loosen ratchet handle (refer to step
3 for tension adjustment of handle).
top or bottom of screen to adjust tilt as shown in fi gure
4.1. The tilt can be adjusted to a maximum of 15°
forward or 5° backward.
Visit the Peerless Web Site at www.peerlessmounts.com
Adjust
Increlok™ and for custom tilt
10°
or 15°. Use
Push or pull from
A
SAFETY/
SECURITY
SCREW
CROSS SECTION
fi g 3.2
IncreLok™
TILT
LOCKING
SCREW
DETAIL 2
RATCHET
HANDLE
7 of 7
ISSUED: 03-26-10 SHEET #: 125-9106-6 12-11-14
For customer care call 1-800-729-0307 or 708-865-8870.
All other brand and product names are trademarks or registered trademarks of their respective owners.
RATCHET
HANDLE
B
&
C
LOCATOR
HOLE
fi g 4.1
© 2013, Peerless Industries, Inc. All rights reserved.
fi g 3.1

Advertisement

loading

  Related Manuals for NEC WMK-3257