Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Danfoss MP20 Series
Summary of Contents for Danfoss MP20 Series
- Page 1 User Manual Remote Control MP20A Receiver www.danfoss.com...
- Page 2 User Manual MP20A Receiver Revision history Table of revisions Date Changed January 2019 Rebranded to Danfoss Power Solutions 0101 © Danfoss | January 2019 BC292562489617en-000101...
-
Page 3: Table Of Contents
Safety instructions General safety....................................4 Safety warnings....................................4 Technical description Dimensions......................................6 Hardware description..................................7 Installation Receiver installation..................................8 Input and output configuration..............................9 Digital outputs..................................... 9 Analog outputs..................................11 Pinout......................................12 Troubleshooting Receiver icon troubleshooting..............................13 © Danfoss | January 2019 BC292562489617en-000101 | 3... -
Page 4: Safety Instructions
• Avoid knocking or dropping the product. • Do not use the product if a failure is detected. Changes or modifications not approved by Danfoss can void the user's authority to operate this product. © Danfoss | January 2019 BC292562489617en-000101... - Page 5 User Manual MP20A Receiver Safety instructions Quick reference precautions © Danfoss | January 2019 BC292562489617en-000101 | 5...
-
Page 6: Technical Description
User Manual MP20A Receiver Technical description MP20 dimensions Dimensions in mm R 2.60 248.91 82.37 R 2.60 R 2.60 R 2.60 81.55 216.00 232.00 © Danfoss | January 2019 BC292562489617en-000101... -
Page 7: Hardware Description
DEUTSCH connector Tether connection External antenna A60 (433) or A70 (870) External EEPROM LCD connection TR800-CE MCX radio CAN connection CAN power supply BUS termination CAN Signaling internal LEDs DEUTSCH connector pinout © Danfoss | January 2019 BC292562489617en-000101 | 7... -
Page 8: Installation
4. Check if the electrical installation and verify if there's an option to connect the neutral or the ground cable. In that case, don't forget to connect the ground cable. The use of fireproof or flame retardant cables are recommended for the connection. © Danfoss | January 2019 BC292562489617en-000101... -
Page 9: Input And Output Configuration
45 (stop) for powering up this group of outputs. Maximum 2A per output. As an alternative, the K5-K12 output group can be connected directly to the external general power supply in order to provide a higher capacity of current. © Danfoss | January 2019 BC292562489617en-000101 | 9... - Page 10 User Manual MP20A Receiver Installation 10 | © Danfoss | January 2019 BC292562489617en-000101...
-
Page 11: Analog Outputs
(stop) for powering up the 1-8 outputs. Maximum 2A per output. nSA1-nSA8 have a common contact at pin 47 of the connector. Pin 47 connects with pin 46 (stop) in order to feed nSA1-nSA8 outputs. Maximum 2A per output. © Danfoss | January 2019 BC292562489617en-000101 | 11... -
Page 12: Pinout
I SA-1 PSWF HAND STOP STOP PW-A81; K1-4 PW-A81; K5-K12 +RRC +12/24V IN-3 IN-2 IN-1 I SA8 I SA7 I SA6 I SA5 I SA4 I SA3 I SA2 I SA-8 I SA1 12 | © Danfoss | January 2019 BC292562489617en-000101... -
Page 13: Troubleshooting
In case of no signal, check if the transmitter is turned on Incorrect ID In case of interference, change frequency channel RF signal detected In case of interference, change frequency channel Mask error Contact your distributor © Danfoss | January 2019 BC292562489617en-000101 | 13... - Page 14 User Manual MP20A Receiver 14 | © Danfoss | January 2019 BC292562489617en-000101...
- Page 15 User Manual MP20A Receiver © Danfoss | January 2019 BC292562489617en-000101 | 15...
- Page 16 Phone: +86 21 3418 5200 Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice. This also applies to products already on order provided that such alterations can be made without subsequent changes being necessary in specifications already agreed.
Need help?
Do you have a question about the MP20 Series and is the answer not in the manual?
Questions and answers