Download Print this page
Danfoss RZ1 User Manual
Danfoss RZ1 User Manual

Danfoss RZ1 User Manual

Z-wave electronic radio-frequency receivers (1-channel)
Hide thumbs Also See for RZ1:

Advertisement

MAKING MODERN LIVING POSSIBLE
Z-Wave Electronic
Radio-Frequency Receivers
(1-Channel)
RZ1 and RZ1-HP

User Guide

Danfoss Heating

Advertisement

loading
Need help?

Need help?

Do you have a question about the RZ1 and is the answer not in the manual?

Questions and answers

Summary of Contents for Danfoss RZ1

  • Page 1: User Guide

    MAKING MODERN LIVING POSSIBLE Z-Wave Electronic Radio-Frequency Receivers (1-Channel) RZ1 and RZ1-HP User Guide Danfoss Heating...
  • Page 2 Danfoss can accept no responsibility for possible errors in catalogues, brochures, and other printed material. All trademarks in this material are property of the respective companies. Danfoss and the Danfoss logotype are trademarks of Danfoss A/S. All rights reserved. RZ1 AND RZ1-HP...
  • Page 3 Thank you for buying a Danfoss product Danfoss Heating...
  • Page 4: Table Of Contents

    ..........................2.0 Operating Modes ..........................3.0 Initial Start Up ............................4.0 Understanding your RZ1 ................7 5.0 Manual Override ................... 8 6.0 Factory Reset ....................9 7.0 Z-Wave supported and controlled classes ........... 9 8.0 Glossary ......................10 RZ1 AND RZ1-HP...
  • Page 5: Operating Modes

    PROGRAMME Mode: used to configure and set-up the RZ1 by the installer. NORMAL OPERATION Mode: should be set in this mode to allow the RZ1 to work correctly, once installed into system. The RZ1 can act as a Z-Wave network primary, or secondary controller within a network. Danfoss Heating...
  • Page 6: Initial Start Up

    3.0 Initial Startup On initial startup the RZ1 will start up in one of two modes with the PROG LED indicating which mode it is in. • P ROG LED continuously ON GREEN: The unit is in a READY STATE. This will be the default startup state for the RZ1 if it was supplied with an RET BZ.
  • Page 7: Understanding Your Rz1

    4.0 Understanding your RZ1 The RZ1 receiver unit uses a combination of coloured LEDs to indicate the current operating mode/output status. For the purpose of this document the indicator lights will be split into two distinct groups; CHANNEL LEDs and PROGRAMME LED. More information is listed below together with explanations of each of the LED colour states.
  • Page 8: Manual Override

    5.0 Manual Override To manually override a channel on the RZ1 receiver you need to press the associated channel button. Depending on the output state at time of override the Channel LED will operate in a set manner: If the channel is already bound/associated with a wireless...
  • Page 9: Factory Reset

    6.0 Factory Reset If for any reason you need to return the RZ1 unit to its factory reset state, or you need to wipe all network information from the unit it is advisable to perform a factory reset. Press PROG to place the receiver in PROGRAMME mode (Red LED illuminated continuously).
  • Page 10: Glossary

    PROG LED is lit and the device is waiting for instructions to switch on or off its output(s). Reset State In the Reset State the RZ1 is reset back to factory defaults and is ready to either be added into an existing network as a secondary controller or to be used to create a network as a primary controller.
  • Page 11 ID server. Any controller in the network can include new nodes to the network, not just the primary device, with a SIS in the network - This increases the functionality of the network. Danfoss Heating...
  • Page 12 Danfoss Randall Ltd. Ampthill Road Bedford MK42 9ER Tel: 0845 1217 400 Fax: 0845 1217 515 Email: danfossrandall@danfoss.com Website: www.danfoss-randall.co.uk Part No. RZ1v03_User...

This manual is also suitable for:

Rz1-hp