Table of Contents
Advertisement
X1 Series
User Manual
6.0kw - 8.0kw
SolaX Power Network Technology(Zhe jiang) Co., Ltd.
Copyright Declaration
The copyright of this manual belongs to SolaX Power Network Technology(Zhe jiang) Co.,
Ltd..
Any corporation or individual should not plagiarize, partially or fully copy (including
software,etc.), and no reproduction or distribution of it in any form or by any means. All rights
reserved. SolaX Power Network Technology (Zhe jiang) Co.,Ltd. . reserves the right of final
interpretation.
614.00368.00
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for SolaX Power X1-6.0-T-D
Summary of Contents for SolaX Power X1-6.0-T-D
- Page 1 Any corporation or individual should not plagiarize, partially or fully copy (including software,etc.), and no reproduction or distribution of it in any form or by any means. All rights reserved. SolaX Power Network Technology (Zhe jiang) Co.,Ltd. . reserves the right of final interpretation.
-
Page 2: Table Of Contents
Contents Contents 1 Note on this Manual 1.1 Scope of Validity 1.2 Target Group 1.3 Symbols Used 2 Safety 2.1 Appropriate Usage 2.2 Important Safety Instructions 2.3 Explanation of Symbols 2.4 EC Directives 3 Introduction 3.1 Basic Features 3.2 Terminals of Inverter 3.3 Dimension 4 Technical Data 4.1 DC Input... -
Page 3: Scope Of Validity
This manual is an integral part of X1 Series, it describes the assembly, installation, commissioning, maintenance and failure of the product. Please read it carefully 8 Decommissioning before operating. 8.1 Dismantling the Inverter 8.2 Packaging X1-6.0-T-D X1-7.0-T-D X1-8.0-T-D 8.3 Storage and Transportation X1-6.0-T-N X1-7.0-T-N X1-8.0-T-N... -
Page 4: Safety
Safety Safety 2 Safety Surge protection devices (SPDs) for PV installation ► Warning! 2.1 Appropriate Usage Over-voltage protection with surge arresters should be provided when the PV power system is installed. The X1 Series are PV inverters which can convert the DC current of the PV generator into The grid connected inverter is not fitted with SPDs in both PV AC current and feed it into the public grid. -
Page 5: Important Safety Instructions
Safety Safety 2.2 Important Safety Instructions Danger! Warning! Danger to life due to high voltages in the inverter! Do not operate the inverter when the device is running. All work must be carried out by qualified electrician. The appliance is not to be used by children or persons with reduced physical sensory or mental capabilities, or lack of Warning! experience and knowledge, unless they have been given... -
Page 6: Explanation Of Symbols
Safety Safety PE Connection and Leakage Current 2.3 Explanation of Symbols This section gives an explanation of all the symbols shown on the inverter and • All inverters incorporate a certified internal Residual Current Device(RCD) in on the type label. order to protect against possible electrocution and fire hazard in case of a malfunction in the PV array, cables or inverter.There are 2 trip thresholds for Symbols on the Inverter... -
Page 7: Ec Directives
Safety Introduction 3. Introduction 2.4 EC Directives This chapter follows the requirements of the European low voltage directives, 3.1 Basic features which contains the safety instructions and conditions of acceptability for the endues system, which you must follow when installing, operating and servicing Thanks for your purchasing with SolaX X1 Series inverter. -
Page 8: Dimension
Introduction Technical Data 4. Technical Data Object Description DC Switch (optional) DC Connector 4.1 DC input RS 485/ NFI/DRM(optional) AC Connector X1-6.0-T-D/ X1-7.0-T-D/ X1-8.0-T-D/ Model Waterproof Valve X1-6.0-T-N X1-7.0-T-N X1-8.0-T-N USB for Upgrade Max. recommended DC power [W] 3000/4000 3000/5000... -
Page 9: Efficiency, Safety And Protection
Technical Data Installation 4.3 Efficiency, Safety and Protection 5. Installation X1-6.0-T-D/ X1-7.0-T-D/ X1-8.0-T-D/ Model 5.1 Check for Transport Damage X1-6.0-T-N X1-7.0-T-N X1-8.0-T-N Inverter+BMU MPPT efficiency 99.90% 99.90% 99.90% Make sure the inverter is intact during transportation. If there are some Euro efficiency... -
Page 10: Installation Precaution
Installation Installation 5.3 Installation Precaution 5.4 Installation Steps Ø Preparation X1 Series inverter is designed for outdoor installation (IP 65). Make sure the installation site meets the following conditions: Below tools are needed before installation. Not be exposed to glare. Not in areas where highly flammable materials are stored. -
Page 11: Connection Of The Inverter
Turn off the DC switch. Table 3 Max. DC Voltage Limitation b) Choose 12 AWG wire to connect the PV module. c) Trip 7mm of insulation from the wire end. X1-6.0-T-D/ X1-7.0-T-D/ X1-8.0-T-D/ d) Separate the DC connector as below. - Page 12 220/230/240V, frequency is 50/60Hz. Other technical requests should comply - Remove the cable nut (with rubber insert) from the back shell. with the requirement of the local public grid. Table 4 Cable and Micro-breaker recommended X1-6.0-T-D/ X1-7.0-T-D/ X1-8.0-T-D/ Model X1-6.0-T-N X1-7.0-T-N...
- Page 13 Installation Installation Selection of Fuses and Cables Note! Main cable(AC line cable)shall be short circuit protected and thermal overload protected. Always fit the input cable with fuse. Normal gG(US:CC or T)fuses will protect the input cable in short circuit situation. They will also prevent damage to adjoining equipment.
- Page 14 Installation Installation ② RS 485/NFI/DRM Ø NFI Connection Steps: a. RS 485 Please see the Quick Guide for NFI Installation for details. RS 485 is one standard communication interface which can transmit the real data from inverter to PC or other monitoring equipments. The PIN de nitions of RS 485/NFI interface are as below.
-
Page 15: Run The Inverter
Installation Installation Upgrade 3) then insert U-disk into the USB port on the bottom of the inverter. Then turn on DC switch or connect the PV connector, the LCD will show User can update the inverter system through a U-disk. picture as below. -
Page 16: Operation Method
Installation Operation Method 6. Operation Method Ø Start inverter Inverter will start automatically when PV panels generate enough energy. Check the status of LED indication and LCD screen, the LED indication should 6.1 Control panel be blue and the LCD screen should display the main interface. If the LED indication is not blue, please check the below: - All the connections are right. -
Page 17: Lcd Function
Operation Method Operation Method 6.2 LCD Function 6.3 LCD Operation ● LCD Digital Display Menu structure The main interface is the default interface, the inverter will automatically jump to this interface when the system started up successfully or not operated for a period of time. The information of the interface is as below. - Page 18 Operation Method Operation Method a) Grid Password This status shows the current grid condition such as voltage, current, output The default password is “0000”for end user, which only allows the user to power and the local consumed power. Pout measures the output of the review the current setting and some easy setting.
- Page 19 Operation Method Operation Method Reactive power control, Reactive standard curve cos φ = f(P) b) Date time This interface is for user to set the system date and time. Increase or decrease the word by pressing up or down button. Press OK to confirm and alternate For VDE ARN 4105, curve cos φ...
- Page 20 Operation Method Operation Method e)P(u) Function h) DRM Function The device is suitable for Australia if the “Enable” is chosen. User can choose whether using the DRM function or not. ﹦﹦﹦ ﹦﹦﹦ P(u) Function ﹦﹦﹦ DRM Function ﹦﹦﹦ >Enable/Disable >Enable< >Mode Select Disable f ) Power limits...
-
Page 21: Troubleshooting
Operation Method Troubleshooting 7. Troubleshooting ● History The history function contains four aspects of the information: Inverter yield, load consume, feed in energy and error logs. 7.1 Trouble shooting Press up and down to select ,and press “OK” to confirm the selection, press “ESC”... - Page 22 Troubleshooting Troubleshooting AC10Minute overvoltage Fault AC10M Volt Fault System will reconnect if the utility is back to normal. Or seek help from us. Grid Frequency out of range ● If your inverter's information panel is not displaying a Fault light, check the following list to make sure that the present state of the installation allows proper operation of the unit.
-
Page 23: Routine Maintenance
Troubleshooting Decommissioning 8. Decommissioning 7.2 Routine maintenance Inverters do not need any maintenance or correction in most condition,but if 8.1 Dismantling the Inverter the inverter often loses power due to overheating,this can be the following reason: Disconnect the inverter from DC Input and AC output. ●...
Need help?
Do you have a question about the X1-6.0-T-D and is the answer not in the manual?
Questions and answers