Procedure 1 Connecting The Wires; Clutch Signal - Pivot 3 drive BLP User Manual

1
procedure
Basic Wiring
(1.5m)
(1.5m)
Brake
Switch
Brake
Option
Connector
ECU, etc...
Note 1: After inserting the connector, pull lightly to make sure that it is securely locked.
• The Brake Switch Connectors will differ depending upon the car model, grade and year, so please sure to check the design in the "Wiring Chart".
• Remove the battery cables from the minus terminals before carrying out the wiring.
Clutch Signal (Use included Clutch Adapter)
Connecting the Clutch Adapter
Red
To Brake Power (normal 12V)
Black
To Earth
Pink
To Pink code of 8-pin Connector
Brown Purple
or
Green
Spare wiring (usually not used)
Basic Wiring
Clutch
Adapter
Unit
8-pin Connector
: Use Cut Connector
(Refer to page 6 [Reference 2] "How to use the Cut Connectors" )
: Use Male Connector
(Refer to page 6 [Reference 3] "How to use the Male Connectors" )
Note: For some car models like
connect directly
Pink
Clutch Switch Signal without using Clutch Adapter.
4
Connecting The Wires
When installing make sure to use the correct Specialized Harness for your car model.
(1.5m)
Earth
Brake Power
(normal 12V)
Brake Switch Signal
(1.5m)
Car Speed Signal
(1.5m)

Clutch Signal

SP
(⇒See the bottom of this page)
Controller
• When connecting to the car side wires, do not only use "electrotap" as this may result in a poor
electrical connection. Please use the supplied "cut connectors" or solder the wires together and
make sure to use insulation tape to securely insulate the wire connection.
• Connect the wires of Clutch switch
signal to the corresponding wires
found in the "Wiring Chart".
• The car which has 2 clutch switch connec-
tors, choose one which works with depress-
ing the clutch pedal.
To Clutch Signal
• Cut off the insulation of the tip of the codes,
among of Brown and Purple and G r e en
c o d e w hi c h yo u n e e d to c o n n e c t , t h e n
bundle the extra code.
(Clutch Switch Signal)
Brown Purple
or
Clutch
Switch
Red
Pink
Black
(Brake Power)
Pink
Brake
Switch
Red
Earth
Black
Fastened two
terminals
86/BRZ
with push button start system,
code from 8-pin Connector of the unit side to
Black
8-pin Connector
(See Note 1)
Red
Gray
Orange
5-pin
Connector
(See Note 1)
Pink
(1.5m)
How to Connect
1. Check the wiring of Clutch Switch Signal ,necessity of
Clutch Adapter and the corresponding wire colors in
the included "Wiring Chart".
2. Connect the wires using included Cut connectors.
(Refer to page 6 [Reference 2] "How to use the Cut Connectors" )
Note that the colors listed in the chart under "Clutch
Adapter Wire Color" are not the colors of the wires on
Clutch
the car side.
e.g. TOYOTA Vitz (from Feb. 2005)
メーカー 車 名
Brake
TOYOTA
ヴィッツ
ア イ
Brown
(MTC-7)
: Use Cut Connector
6-pin Connector
(See Note 1)
Unit
(0.5m)
Special Model
Specific Harness
(sold separately)
Accelerator Connector
Wiring
Chart
Clutch
Pedal
クラッチ関係
接続記号
クラッチ クラッチ
スイ ッチ アダプター
クラッチアダプター
コネクター
○ ：使用する のコード色
形状
×：使用しない
茶
MTC-7 ○ ア
H17.
Switch Connector
Wire leading
from Clutch Adapter
Accelerator
Clutch
Switch
Wiring
Chart
ユニットの
コード色
紫 ピンク
Connection
letter
イ
ア
Brown