Advertisement
Advertisement
Table of Contents
Related Manuals for Eaton Char-Lynn 4000 Series
Summary of Contents for Eaton Char-Lynn 4000 Series
- Page 2 4000 Series Char-Lynn Motors Shuttle (Two Way) Balance Check Plug Assembly Spring Plug Ring Valve Assembly Plug Poppet Outer Valve Assembly Spring Spring Plug Assembly Face Seal Spring Seal Valve Sleeve, Dash Pot Plate Plug Ball Piston Shuttle Seal Sleeve, Dash Pot Housing, Bearing Drive Plug...
- Page 3 No. E10 The following tools are not necessary for disassembly and reassembly but are extremely helpfull — Alignment studs (2), see dimensions below Available by special order, contact Eaton Corp., Hydraulics Division Service Dept. 200 mm [8 inch] 25 mm Approx.
- Page 4 4000 Series Char-Lynn Motors Disassembly Cleanliness is extremely important when repairing a hydraulic motor. 3 Lift valve housing straight up. If done carefully, the springs and Work in a clean area. Before disconnecting the lines, clean port area of balance ring subassembly will remain on valve for easy removal. motor thoroughly.
- Page 5 4000 Series Char-Lynn Motors Disassembly Valve Drive Valve Plate Seal Seal Figure 7 Figure 5 16 Use a stud remover or vise grips to remove studs (earlier models only). Clamp bearing housing in vise as shown in Figure 7. Loosen 8 9 Remove valve plate.
- Page 6 Note: Individual parts of the shaft and bearing assembly are not sold separately and must be replaced as a unit. Bearing Housing Figure 10 Note: Shaft face seal installation tool is available by special order. Contact Eaton Corporation, Hydraulics Division (Service Department). 600468 (-004) 600421-2 (-006). Reassembly Shaft and Bearing Assembly Check all mating surfaces.
- Page 7 Timing parts include: 1. Geroler Note: Bullet 600463 for 1-1/4 inch diameter shafts available by 2. Valve drive special order through Eaton Hydraulics Division service department. 3. Valve Plate 4. Valve Rotate Valve Clockwise Anyone of 6 Ports...
- Page 8 4000 Series Char-Lynn Motors Reassembly 41 Apply a light film of petroleum jelly on 82,3 mm [3.24 inch] I.D. 36 Apply a light film of petroleum jelly on 88,6 mm [3.49 inch] I.D. seal. Install seal in outside seal groove of valve housing. seal.
- Page 9 4000 Series Char-Lynn Motors Reassembly 44 Insert your finger through port of housing. Apply pressure to side 45 Install and finger tighten 2 bolts (or studs for earlier models) of balance ring assembly. Hold ring in position until valve housing is opposite alignment studs.
- Page 10 4000 Series Char-Lynn Motors Reassembly Important: This motor requires Loctite in threaded holes of mounting flange. Follow these procedures: Attention: Adequate Loctite penetration and sealing depend highly on cleanliness Do not use and dryness of threads. Use a non-petroleum base solvent to clean more than excess oil from threads of flange after disassembly.
- Page 11 Last 3. Part Name Year 01 Number Eaton Corp. Hydraulics Div. Eden Prairie, MN 55344 For more detailed information contact Eaton Corp. Hydraulics Thru 52 of Year Product Number Division 15151 Highway 5 Eden Prairie, MN 55344. 109 0000 000 Specifications and performance data, Catalog No.
- Page 12 Tel: (44) 23 92 486 451 Fax: 952 97 4-7722 Tel: (61) 3 9319 8222 Fax: (44) 23 92 487 110 www.hydraulics.eaton.com Fax: (61) 3 9318 5714 © 2016 Eaton Corporation Char-Lynn All rights reserved Printed in USA Document No. 07-118 August 2016...
Need help?
Do you have a question about the Char-Lynn 4000 Series and is the answer not in the manual?
Questions and answers