Advertisement
Quick Links
Technical Data
Auxiliary switches
Feedback
Power supply
Power consumption
Control signal
Running time through
90º
Torque
Electrical connection
Inlet bushing
Angle of rotation
Direction of rotation
Ambient temperature
Storage temperature
Relative Humidity
Weight
Ingress protection
Dimensions
D
C
Caution
We strongly recommend that all neptronic products be wired to a separate transformer and that transformer shall service only neptronic products. This precaution will
prevent interference with, and/or possible damage to incompatible equipment.
When multiple actuators are wired on a single transformer, polarity must be observed. Long wiring runs create voltage drop which may affect the actuator performance.
BT00/080619
Feature:
• Mounts easy on round
& square shaft (with option –8).
• Power supply high voltage 120 or 240 VAC.
• External clutch for manual adjustments.
• Maintenance free.
• Position indicator.
• Feedback
(on model 105 & 205).
• Auxiliary switches
(on model 120 & 220).
BT100
BT105
BBTHV1100A
BBTHV1105A
No
No
No
Yes
110 to 130 VAC 50/60Hz
4 Watts at 120 VAC (0.166A AC)
0 to 90 degrees, mechanically adjustable (factory set with 90º stroke)
Reversible, Clockwise (CW) or Counterclockwise (CCW) (factory set with CW direction)
IP54 equivalent to Nema type 3R if water tight inlet bushings (not supplied NEP617) are installed
Warning: Do not press the clutch when actuator is powered
A
B
Specification & Installation instructions
BT120
BBTHV1121A
BBTHV1200A
Yes (2)
No
3 wire / 2 position, 3 wire / 3 point floating
20 to 30 sec Torque dependant
50 in.lb. [5,6 Nm] at rated voltage
2
18 AWG [0.8 mm
] minimum
2 inlet bushing of 5/8 in [15.9 mm] & 7/8 in [22.2 mm]
-22ºF to +122ºF [-30ºC to +50ºC]
-22ºF to +122ºF [-30ºC to +50ºC]
5 to 95 % non condensing.
3 lbs. [1.4 kg]
IP22 equivalent to Nema type 2,
Dimension
A
B
C
D
Old Number
BBTHV1100A
BBTHV1105A
BBTHV1121A
BBTHV1200A
BBTHV1205A
BBTHV1221A
BT200
BT205
BBTHV1205A
No
No
No
Yes
220 to 250 VAC 50/60Hz
7 Watts at 240 VAC (0.166A AC)
Inches
Metric (mm)
1.50
3.26
6.60
3.01
Actuator
BT100
BT105
BT120
BT200
BT205
BT220
BT220
BBTHV1221A
Yes (2)
No
38.1
82.8
167.5
76.4
1
Advertisement
Related Manuals for Neptronic BBTHV1100A
Summary of Contents for Neptronic BBTHV1100A
- Page 1 76.4 Caution We strongly recommend that all neptronic products be wired to a separate transformer and that transformer shall service only neptronic products. This precaution will prevent interference with, and/or possible damage to incompatible equipment. When multiple actuators are wired on a single transformer, polarity must be observed. Long wiring runs create voltage drop which may affect the actuator performance.
- Page 2 BT100/105/120/200/205/220 Specification & Installation instruction Mechanical installation Manually close the damper blades and positioned the actuator at 0º or 90º. Slide the actuator onto the shaft. Tighten the nuts on the “U” bolt to the shaft with a 8mm wrench to a torque of 60 in.lb. [6,7 Nm]. MOUNTING BRACKET Slide the mounting bracket under the actuator.