Related Manuals for Northern IP4DIR100
Summary of Contents for Northern IP4DIR100
- Page 1 Installation & Quick Setup Guide ♦ ♦ 3625 Cincinnati Avenue, Rocklin, CA 95765 855-388-7422 www.northernvideo.com Rev. 061218...
- Page 2 IP4DIR100 Series IP Dome Camera · Quick Start Guide About this Manual This Manual is applicable to IP4DIR100 & IP4DIR1004MM Network Cameras. The Manual includes instructions for using and managing the product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons.
- Page 3 IP4DIR100 Series IP Dome Camera · Quick Start Guide Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
- Page 4 IP4DIR100 Series IP Dome Camera · Quick Start Guide 2. This device must accept any interference received, including interference that may cause undesired operation. EU Conformity Statement This product and - if applicable - the supplied accessories too are marked with "CE" and comply...
- Page 5 IP4DIR100 Series IP Dome Camera · Quick Start Guide Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into “Warnings” and “Cautions” Warnings: Serious injury or death may occur if any of the warnings are neglected.
- Page 6 IP4DIR100 Series IP Dome Camera · Quick Start Guide ● Do not connect several devices to one power adapter as adapter overload may cause over-heating or a fire hazard. ● Please make sure that the plug is firmly connected to the power socket.
- Page 7 IP4DIR100 Series IP Dome Camera · Quick Start Guide ● Do not place the camera in extremely hot, cold (the operating temperature shall be -30°C to +60°C), dusty or damp locations, and do not expose it to high electromagnetic radiation.
-
Page 8: Table Of Contents
IP4DIR100 Series IP Dome Camera · Quick Start Guide Table of Contents 1 Appearance Description ..............8 1.1 Overview of IP4DIR100 Series Camera ......8 2 Installation ..................11 Memory Card Installation ..........12 Ceiling Mounting ............13 Mounting with Brackets ..........17 2.4 Network Cable Waterproof Jacket Installation .... -
Page 9: Appearance Description
IP4DIR100 Series IP Dome Camera · Quick Start Guide 1 Appearance Description Overview of IP4DIR100 Series Camera DC12VIN... - Page 10 IP4DIR100 Series IP Dome Camera · Quick Start Guide Figure 1-1 Overview of IP4DIR100 Series Camera Table 1-1 Description of IP4DIR100 Series Camera Description Power supply interface (12 VDC) Audio input and output interface Alarm input and output interface RJ45 self-adaptive network interface (PoE)
- Page 11 IP4DIR100 Series IP Dome Camera · Quick Start Guide Reset button Note: To reset the camera to default status you first need to remove power from the camera. Then press and hold the reset button while re-applying power, continue to hold the reset button for at...
-
Page 12: Installation
IP4DIR100 Series IP Dome Camera · Quick Start Guide 2 Installation Before you start: ● Make sure the device in the package is in good condition and all the assembly parts are included. ● The standard power supply is 12 VDC or PoE (802.3 af), please make sure your power supply matches with your camera. -
Page 13: Memory Card Installation
IP4DIR100 Series IP Dome Camera · Quick Start Guide Memory Card Installation This cameras supports memory card as local storage, you can follow the steps to mount and unmount the memory card. Steps: Loosen the screws on the bubble. Remove the bubble to expose the memory card slot. -
Page 14: Ceiling Mounting
IP4DIR100 Series IP Dome Camera · Quick Start Guide Figure 2-2 Insert Memory Card (Optional) To unmount the memory card, push to get it ejected. Ceiling Mounting Steps: Paste the drill template to desired mounting place. Drill the screw holes on the ceiling according to the drill... - Page 15 IP4DIR100 Series IP Dome Camera · Quick Start Guide Drill Template Hole A: for cables routed through the ceiling Screw hole 1: for Mounting Base Figure 2-3 Drill Template Notes: ● If you choose to route cable through the ceiling, cut a cable hole according to Hole A on drill template.
- Page 16 IP4DIR100 Series IP Dome Camera · Quick Start Guide Route the cables and fix the mounting base on the ceiling with three screws. Figure 2-5 Fix the Mounting Base Adjust surveillance angle. Loosen one tilting adjust adjusting screw to adjust the tilting position.
- Page 17 IP4DIR100 Series IP Dome Camera · Quick Start Guide Figure 2-6 Angle Adjustment of Camera Install the bubble back to the camera. Figure 2-7 Install Bubble...
-
Page 18: Mounting With Brackets
IP4DIR100 Series IP Dome Camera · Quick Start Guide Mounting with Brackets This camera supports various mounting accessories. Wall Mounting is used as an example in this manual. The wall mounting bracket is not included in the package. You need to purchase one separately, if you adopt this mounting type. - Page 19 IP4DIR100 Series IP Dome Camera · Quick Start Guide 3. Unscrew the bubble of the camera. 4. (Optional) Insert the memory card to the camera, if your camera supports memory card installation. Refer to Section 2.1. 5. Route the cables and fix the camera to the cap of the wall mounting bracket with three supplied self-tapping screws.
- Page 20 IP4DIR100 Series IP Dome Camera · Quick Start Guide Figure 2-10 Fix the Indoor WM110 Wall Mounting Bracket to Wall 7. Adjust surveillance angle of camera. Refer to Step 4 in Section 2.2. 8. Install the bubble back to the camera.
- Page 21 IP4DIR100 Series IP Dome Camera · Quick Start Guide 2.3.1 Wall Mounting with Outdoor WMTS Junction Box The WMTS outdoor wall mounting bracket with junction box is not included in the package. You need to purchase one separately, if you adopt this mounting type.
- Page 22 IP4DIR100 Series IP Dome Camera · Quick Start Guide Cover Figure 2-13 Unscrew the Cover 4. Route and connect the cables. Source cables of network, power, etc., go in from the side outlet of the junction box. Camera cables go in from the cap and the bracket.
- Page 23 IP4DIR100 Series IP Dome Camera · Quick Start Guide Camera Cable Source Cable Figure 2-14 Cable Routing 6. Unscrew the bubble of the camera. 7. (Optional) Insert the memory card to the camera, if your camera supports memory card installation. Refer to Section 2.1.
- Page 24 IP4DIR100 Series IP Dome Camera · Quick Start Guide Figure 2-15 Fix the Camera to DPC110 Cap 9. Adjust surveillance angle of camera. Refer to Step 4 in Section 2.2. 10. Install the bubble back to the camera.
-
Page 25: Network Cable Waterproof Jacket Installation
IP4DIR100 Series IP Dome Camera · Quick Start Guide Figure 2-16 Install the Bubble Network Cable Waterproof Jacket Installation Purpose: If the camera is installed outdoor, you should use the waterproof accessory for the network cable after the camera is secured on the installation surface. - Page 26 IP4DIR100 Series IP Dome Camera · Quick Start Guide Table 2-1 Components Components Camera’s Network Interface Socket O-Type Gasket Network Plug Waterproof Endcap Waterproof Rubber Gasket Lock Nut Network Cable from Router/Switch Steps: Feed the plugless network cable ⑦ through the lock nut ⑥, waterproof rubber gasket ⑤...
- Page 27 IP4DIR100 Series IP Dome Camera · Quick Start Guide Insert the waterproof rubber gasket ⑤ into the waterproof endcap ④, and secure lock nut ⑥ with the waterproof endcap ④. Align the snap on the waterproof endcap ④ with the notch on the camera’s network interface socket ①, and then secure the...
-
Page 28: Set The Network Camera Over The Lan
IP4DIR100 Series IP Dome Camera · Quick Start Guide 3 Set the Network Camera over the Note: You shall acknowledge that the use of the product with Internet access might be under network security risks. For avoidance of any network attacks and information leakage, please strengthen your own protection. -
Page 29: Activate The Camera
IP4DIR100 Series IP Dome Camera · Quick Start Guide Activate the Camera You are required to activate the camera first by setting a strong password for it before you can use the camera. Activation via Web Browser, Activation via SADP, and Activation via Client Software are all supported. - Page 30 IP4DIR100 Series IP Dome Camera · Quick Start Guide Activation Interface (Web) Figure 3-3 Create a password and input the password into the password field. STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including...
- Page 31 IP4DIR100 Series IP Dome Camera · Quick Start Guide activate the camera, please refer to the User Manual of Network Camera for other two activation methods. Steps: 1. Run the SADP software to search the online devices. 2. Check the device status from the device list, and select the inactive device.
-
Page 32: Modify The Ip Address
IP4DIR100 Series IP Dome Camera · Quick Start Guide STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product. - Page 33 IP4DIR100 Series IP Dome Camera · Quick Start Guide Steps: 1. Run the SADP software. 2. Select an activate device. 3. Change the device IP address to the same subnet with your computer by either modifying the IP address manually or checking Enable DHCP.
- Page 34 IP4DIR100 Series IP Dome Camera · Quick Start Guide Note: You can enable the Guarding Vision service for the device during activation. Refer to Chapter 5.1 for detailed information. 4. Input the admin password and click Modify to activate your IP address modification.
-
Page 35: Access Via Web Browser
IP4DIR100 Series IP Dome Camera · Quick Start Guide 4 Access via Web Browser System Requirement: Operating System: Microsoft Windows XP SP1 and above version CPU: 2.0 GHz or higher RAM: 1G or higher Display: 1024×768 resolution or higher Web Browser: Internet Explorer 8.0 and above version, Apple Safari 5.0.2 and above version, Mozilla Firefox 5.0 and above version and... - Page 36 IP4DIR100 Series IP Dome Camera · Quick Start Guide 4. Click Login. Login Interface Figure 4-1 5. Install the plug-in before viewing the live video and managing the camera. Please follow the installation prompts to install the plug-in. Note: You may have to close the web browser to finish the installation of the plug-in.
-
Page 37: Operate Via Guarding Vision App
IP4DIR100 Series IP Dome Camera · Quick Start Guide 5 Operate via Guarding Vision App Purpose: Guarding Vision is an application for mobile devices. With the App, you can view live image of the camera, receive alarm notification and so on. - Page 38 IP4DIR100 Series IP Dome Camera · Quick Start Guide “Privacy Policy” Service” Verification Code Setting (SADP) Figure 5-1 Note: The verification code is required when you add the camera to Guarding Vision app. 3. Click and read "Terms of Service" and "Privacy Policy".
- Page 39 IP4DIR100 Series IP Dome Camera · Quick Start Guide Steps: 1. Access the camera through web browser. Refer to Chapter 4. 2. Enter platform access configuration interface: Configuration > Network > Advanced Settings > Platform Access. Guarding Vision dev.guardingvision.com Platform Access Configuration (Web) Figure 5-2 3.
-
Page 40: Guarding Vision Setup
IP4DIR100 Series IP Dome Camera · Quick Start Guide Guarding Vision Setup Steps: 1. Download and install the Guarding Vision app by searching “Guarding Vision” in App Store or Google Play 2. Launch the app and register for a Guarding Vision user account. - Page 41 IP4DIR100 Series IP Dome Camera · Quick Start Guide You can find the QR code on the camera or on the cover of the Quick Start Guide of the camera in the package. Figure 5-4 Scan QR Code Note: If the QR code is missing or too blur to be recognized, you can also...
-
Page 42: Initialize The Memory Card
IP4DIR100 Series IP Dome Camera · Quick Start Guide Initialize the Memory Card Steps: Check the memory card status by tapping on the Storage Status in the Device Settings interface. If the memory card status displays as Uninitialized, tap to initialize it. - Page 43 UD07706N...