Related Manuals for Northern IP4TIR100
Summary of Contents for Northern IP4TIR100
- Page 1 Installation & Quick Setup Guide ♦ ♦ 3625 Cincinnati Avenue, Rocklin, CA 95765 855-388-7422 www.northernvideo.com Rev. 061218...
- Page 2 IP4TIR100 IP Turret Camera · Quick Start Guide About this Manual This Manual is applicable to IP4TIR100 Network Camera. The Manual includes instructions for using and managing the product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons.
- Page 3 IP4TIR100 IP Turret Camera · Quick Start Guide Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
- Page 4 IP4TIR100 IP Turret Camera · Quick Start Guide FCC Conditions This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation.
- Page 5 IP4TIR100 IP Turret Camera · Quick Start Guide supplier or to a designated collection point. For more information see:www.recyclethis.info Industry Canada ICES-003 Compliance This device meets the CAN ICES-3 (B)/NMB-3(B) standards requirements. Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss.
- Page 6 IP4TIR100 IP Turret Camera · Quick Start Guide ● In the use of the product, you must be in strict compliance with the electrical safety regulations of the nation and region. Please refer to technical specifications for detailed information. ● Input voltage should meet both the SELV (Safety Extra Low Voltage) and the Limited Power Source with 12 VDC according to the IEC60950-1 standard.
- Page 7 IP4TIR100 IP Turret Camera · Quick Start Guide ● Do not aim the camera at the sun or extra bright places. Blooming or smearing may occur otherwise (which is not a malfunction), and affect the endurance of sensor at the same time.
-
Page 8: Table Of Contents
IP4TIR100 IP Turret Camera · Quick Start Guide Table of Contents 1 Appearance Description ..............8 1.1 Overview of IP4TIR100 Turret Camera ......8 2 Installation ..................10 2.1 Ceiling Mounting ............10 2.2 Mounting with Brackets ..........14 2.2.1 Wall Mounting ............ 15 2.3 Network Cable Waterproof Accessory Installation .. -
Page 9: Appearance Description
IP4TIR100 IP Turret Camera · Quick Start Guide 1 Appearance Description Overview of IP4TIR100 Turret Camera Figure 1-1 IP4TIR100 Turret Camera Table 1-1 Description Description Description Trim Ring Power Cord 10M/100M Self-adaptive Enclosure Ethernet Interface (PoE) RST (Reset) Button Mounting Base... - Page 10 IP4TIR100 IP Turret Camera · Quick Start Guide Notes: This turret camera supports PoE power supply. You can power the camera by connecting both DC 12V interface and the Ethernet interface. Or you can connect the Ethernet interface only.
-
Page 11: Installation
IP4TIR100 IP Turret Camera · Quick Start Guide 2 Installation Before you start: ● Make sure the device in the package is in good condition and all the assembly parts are included. ● The standard power supply is 12 VDC or PoE (802.3af), please make sure your power supply matches with your camera. - Page 12 IP4TIR100 IP Turret Camera · Quick Start Guide Separate the camera and the enclosure. ① ③ Fixing Screw ② Figure 2-1 Disassemble the Camera Install memory card. Unscrew the memory card slot cover. Insert the memory card. Memory Card Figure 2-2...
- Page 13 IP4TIR100 IP Turret Camera · Quick Start Guide Paste the drill template to desired mounting place. Drill the screw holes (for expansion screws) and the cable hole on the ceiling according to the drill template. Note: If the camera is installed to a wooden wall, use self-tapping screws instead of expansion screws.
- Page 14 IP4TIR100 IP Turret Camera · Quick Start Guide Drill Template Mounting Base Figure 2-4 Fix Mounting Base Connect the corresponding power/network cable. Refer to the section 2.3 for the waterproof accessory installation if the camera is installed in the outdoor.
-
Page 15: Mounting With Brackets
IP4TIR100 IP Turret Camera · Quick Start Guide Pan: 0° to 360° Rotate: Tilt: 0° to 360° 0° to 75° Figure 2-6 Adjust Surveillance Angle Attach the trim ring to the camera and rotate the trim ring clockwise to get it secured. -
Page 16: Wall Mounting
IP4TIR100 IP Turret Camera · Quick Start Guide 2.2.1 Wall Mounting Steps: Mark the screw holes on desired mounting place. Figure 2-8 Dimension of Demonstrated Wall Mounting Bracket Drill four screw holes with a Φ10 mm drill. Route the cables and fix the bracket with four M6 expansion bolts. - Page 17 IP4TIR100 IP Turret Camera · Quick Start Guide Mounting Base Figure 2-9 Fix Mounting Base Connect the corresponding power/network cable. Refer to the section 2.3 for the waterproof accessory installation if the camera is installed in the outdoor. Install the camera and the enclosure to the mounting base, adjust the surveillance angle, and fix the trim ring.
-
Page 18: Network Cable Waterproof Accessory Installation
IP4TIR100 IP Turret Camera · Quick Start Guide Network Cable Waterproof Accessory Installation Purpose: If the camera is installed outdoor, you should use the waterproof accessory for the network cable after the camera is secured on the installation surface. ① ②... - Page 19 IP4TIR100 IP Turret Camera · Quick Start Guide Feed the plugless network cable ⑦ through the lock nut ⑥, waterproof rubber gasket ⑤ (rubber gasket inset ridge must face waterproof endcap), and the waterproof endcap ④ in order. Crimp an RJ-45 network plug ③onto the end of the cable, taking care to insert the twisted pairs of wires in correct order.
- Page 20 IP4TIR100 IP Turret Camera · Quick Start Guide Align the snap and notch. i. Insert into ⑤ ④ ii. Secure with ⑥ ④ Camera Switch/Router Figure 2-12 Waterproof Accessory Installation...
-
Page 21: Set The Network Camera Over The Lan
IP4TIR100 IP Turret Camera · Quick Start Guide 3 Set the Network Camera over the Note: You shall acknowledge that the use of the product with Internet access might be under network security risks. For avoidance of any network attacks and information leakage, please strengthen your own protection. -
Page 22: Activate The Camera
IP4TIR100 IP Turret Camera · Quick Start Guide Activate the Camera You are required to activate the camera first by setting a strong password for it before you can use the camera. Activation via Web Browser, Activation via SADP, and Activation via Client Software are all supported. -
Page 23: Activation Via Sadp Software
IP4TIR100 IP Turret Camera · Quick Start Guide Figure 3-3 Activation Interface (Web) 3. Create a password and input the password into the password field. STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including... - Page 24 IP4TIR100 IP Turret Camera · Quick Start Guide Get the SADP software from the supplied disk or the official website, and install the SADP according to the prompts. Follow the steps to activate the camera, please refer to the User Manual of Network Camera for other two activation methods.
-
Page 25: Modify The Ip Address
IP4TIR100 IP Turret Camera · Quick Start Guide STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product. - Page 26 IP4TIR100 IP Turret Camera · Quick Start Guide Steps: 1. Run the SADP software. 2. Select an activate device. 3. Change the device IP address to the same subnet with your computer by either modifying the IP address manually or checking Enable DHCP.
- Page 27 IP4TIR100 IP Turret Camera · Quick Start Guide Note: You can enable the Guarding Vision service for the device during activation. Refer to Chapter 5.1 for detailed information. 4. Input the admin password and click Modify to activate your IP address modification.
-
Page 28: Access Via Web Browser
IP4TIR100 IP Turret Camera · Quick Start Guide 4 Access via Web Browser System Requirement: Operating System: Microsoft Windows XP SP1 and above version CPU: 2.0 GHz or higher RAM: 1G or higher Display: 1024×768 resolution or higher Web Browser: Internet Explorer 8.0 and above version, Apple Safari 5.0.2 and above version, Mozilla Firefox 5.0 and above version and... - Page 29 IP4TIR100 IP Turret Camera · Quick Start Guide Figure 4-1 Login Interface 5. Install the plug-in before viewing the live video and managing the camera. Please follow the installation prompts to install the plug-in. Note: You may have to close the web browser to finish the installation of the plug-in.
-
Page 30: Operate Via Guarding Vision App
IP4TIR100 IP Turret Camera · Quick Start Guide 5 Operate via Guarding Vision App Purpose: Guarding Vision is an application for mobile devices. With the App, you can view live image of the camera, receive alarm notification and so on. -
Page 31: Enable Guarding Vision Via Web Browser
IP4TIR100 IP Turret Camera · Quick Start Guide Service” “Privacy Policy” Figure 5-1 Verification Code Setting (SADP) Note: The verification code is required when you add the camera to Guarding Vision app. 3. Click and read "Terms of Service" and "Privacy Policy". - Page 32 IP4TIR100 IP Turret Camera · Quick Start Guide Steps: 1. Access the camera through web browser. Refer to Chapter 4. 2. Enter platform access configuration interface: Configuration > Network > Advanced Settings > Platform Access. Guarding Vision dev.guardingvision.com Figure 5-2 Platform Access Configuration (Web) 3.
-
Page 33: Guarding Vision Setup
IP4TIR100 IP Turret Camera · Quick Start Guide Guarding Vision Setup Steps: 1. Download and install the Guarding Vision app by searching “Guarding Vision” in App Store or Google Play 2. Launch the app and register for a Guarding Vision user account. - Page 34 IP4TIR100 IP Turret Camera · Quick Start Guide You can find the QR code on the camera or on the cover of the Quick Start Guide of the camera in the package. Figure 5-4 Scan QR Code Note: If the QR code is missing or too blur to be recognized, you can also...
-
Page 35: Initialize The Memory Card
IP4TIR100 IP Turret Camera · Quick Start Guide Initialize the Memory Card Steps: Check the memory card status by tapping on the Storage Status in the Device Settings interface. If the memory card status displays as Uninitialized, tap to initialize it.
Need help?
Do you have a question about the IP4TIR100 and is the answer not in the manual?
Questions and answers