Subscribe to Our Youtube Channel
Related Manuals for Northern IP4AFBIR150
Summary of Contents for Northern IP4AFBIR150
- Page 1 Installation & Quick Setup Guide ♦ ♦ 3625 Cincinnati Avenue, Rocklin, CA 95765 855-388-7422 www.northernvideo.com Rev. 061218...
- Page 2 IP4AFBIR150 IP Bullet Camera · Quick Start Guide About this Manual The Manual includes instructions for using and managing the product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons.
- Page 3 IP4AFBIR150 IP Bullet Camera · Quick Start Guide Regulatory Information FCC Information FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
- Page 4 IP4AFBIR150 IP Bullet Camera · Quick Start Guide standards listed under the EMC Directive 2014/30/EU, the RoHS Directive 2011/65/EU. 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper...
- Page 5 IP4AFBIR150 IP Bullet Camera · Quick Start Guide Warnings: Serious injury or death may occur if any of the warnings are neglected. Cautions: Injury or equipment damage may occur if any of the cautions are neglected. Warnings Follow these Cautions Follow these...
- Page 6 IP4AFBIR150 IP Bullet Camera · Quick Start Guide ● Please make sure that the plug is firmly connected to the power socket. When the product is mounted on wall or ceiling, the device shall be firmly fixed. ● If smoke, odor or noise rise from the device, turn off the power at once and unplug the power cable, and then please contact the service center.
- Page 7 IP4AFBIR150 IP Bullet Camera · Quick Start Guide ● To avoid heat accumulation, good ventilation is required for operating environment. ● Keep internal components of the camera away from liquid while in use. ● While in shipping, the camera shall be packed in its original packing, or packing of the same quality.
-
Page 8: Table Of Contents
IP4AFBIR150 IP Bullet Camera · Quick Start Guide Table of Contents 1 Appearance Description ..............8 2 Installation ..................11 2.1 Memory Card Installation ..........11 2.2 Camera Mounting ............13 2.2.1 Ceiling/Wall Mount ..........13 2.2.2 Mounting with a Gang Box ......... 19 3 Setting the Network Camera over the LAN ........ -
Page 9: Appearance Description
IP4AFBIR150 IP Bullet Camera · Quick Start Guide 1 Appearance Description The overview of the bullet camera is shown below. 12 13 Figure 1-1 Overview of the Camera... - Page 10 IP4AFBIR150 IP Bullet Camera · Quick Start Guide Table 1-1 Description Description Sun Shield Lens Front Cover Three-axis Adjustment Bracket Junction Box Side Outlet Cover Alarm Interface Audio Interface RJ 45 Network Interface Power Interface Cover Reset Button Video Out (BNC)
- Page 11 IP4AFBIR150 IP Bullet Camera · Quick Start Guide Ethernet interface. Or you can connect the Ethernet interface only. To reset the camera to default status you first need to remove power from the camera. Then press and hold the reset button while re-applying power, continue to hold the reset button for at least 15 seconds after applying power to default the camera.
-
Page 12: Installation
IP4AFBIR150 IP Bullet Camera · Quick Start Guide Installation Before you start: ● Make sure the device in the package is in good condition and all the assembly parts are included. ● The standard power supply is 12 VDC or PoE (802.3at). Make sure your power supply matches with your camera. - Page 13 IP4AFBIR150 IP Bullet Camera · Quick Start Guide Allen Wrench Figure 2-1 Remove the Cover of the Memory Card Slot 2. Insert the memory card into the card slot. Figure 2-2 Insert the Memory Card 3. Tighten the screws to replace the slot cover.
-
Page 14: Camera Mounting
IP4AFBIR150 IP Bullet Camera · Quick Start Guide Figure 2-3 Replace the Slot Cover 2.2 Camera Mounting 2.2.1 Ceiling/Wall Mount Steps: 1. Drill screw holes in the wall/ceiling according to the holes 1 on the supplied adapter. - Page 15 IP4AFBIR150 IP Bullet Camera · Quick Start Guide 83.5 Φ40 Unit: mm Figure 2-4 Drill Holes in the Wall/Ceiling 2. Secure the adapter to the wall/ceiling with the screws. Figure 2-5 Install the Adapter 3. Loosen the screws to remove the junction box.
- Page 16 IP4AFBIR150 IP Bullet Camera · Quick Start Guide Figure 2-6 Remove the Junction Box 4. Route the cables through the sealing plugs in the junction box. Pierce the sealing plugs on the junction box. Thread cables through the sealing plugs.
- Page 17 IP4AFBIR150 IP Bullet Camera · Quick Start Guide Figure 2-8 Route the Cables through the Junction Box 5. Secure the junction box in the wall/ceiling with screws. Figure 2-9 Secure the Junction Box 6. Hook the camera to the junction box with the safety rope and...
- Page 18 IP4AFBIR150 IP Bullet Camera · Quick Start Guide Safety Rope Figure 2-10 Hook the Camera to the Junction Box 7. Secure the camera to the junction box with the screws. Figure 2-11 Secure the Camera 8. Adjust the view angle.
- Page 19 IP4AFBIR150 IP Bullet Camera · Quick Start Guide Steps: Loosen the lock screw using the supplied Allen wrench. Adjust the view angle of the camera. The adjusting range of the panning is from 0° to 360°, the tilting is from 0° to 90° and the rotation is from 0°...
-
Page 20: Mounting With A Gang Box
IP4AFBIR150 IP Bullet Camera · Quick Start Guide 2.2.2 Mounting with a Gang Box Before you start: The gang box is not included in the package. You need to prepare one for this mounting type. Steps: 1. Secure the adapter to a gang box with the screws. -
Page 21: Setting The Network Camera Over The Lan
IP4AFBIR150 IP Bullet Camera · Quick Start Guide 3 Setting the Network Camera over the Note: You shall acknowledge that the use of the product with Internet access might be under network security risks. For avoidance of any network attacks and information leakage, please strengthen your own protection. -
Page 22: Activating The Camera
IP4AFBIR150 IP Bullet Camera · Quick Start Guide Activating the Camera You are required to activate the camera first by setting a strong password for it before you can use the camera. Activation via Web Browser, Activation via SADP, and Activation via Client Software are all supported. -
Page 23: Activation Via Sadp Software
IP4AFBIR150 IP Bullet Camera · Quick Start Guide Figure 3-3 Activation Interface(Web) 3. Create a password and input the password into the password field. STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including... - Page 24 IP4AFBIR150 IP Bullet Camera · Quick Start Guide Get the SADP software from the supplied disk or the official website, and install the SADP according to the prompts. Follow the steps to activate the camera. Steps: 1. Run the SADP software to search the online devices.
-
Page 25: Modifying The Ip Address
IP4AFBIR150 IP Bullet Camera · Quick Start Guide STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product. - Page 26 IP4AFBIR150 IP Bullet Camera · Quick Start Guide Steps: 1. Run the SADP software. 2. Select an active device. 3. Change the device IP address to the same subnet with your computer by either modifying the IP address manually or checking the checkbox of Enable DHCP.
- Page 27 IP4AFBIR150 IP Bullet Camera · Quick Start Guide Note: You can enable the Guarding Vision service for the device during activation. Refer to Chapter 5.1 for detailed information. 4. Input the admin password and click Modify to activate your IP address modification.
-
Page 28: Accessing Via Web Browser
4 Accessing via Web Browser System Requirement: Operating System: Microsoft Windows XP SP1 and above version CPU: 2.0 GHz or higher RAM: 1G or higher Display: 1024×768 resolution or higher Web Browser: Internet Explorer 8.0 and above version, Apple Safari 5.0.2 and above version, Mozilla Firefox 5.0 and above version and Google Chrome 18 and above version Steps:... - Page 29 4. Click Login. Figure 4-1 Login Interface 5. Install the plug-in before viewing the live video and managing the camera. Follow the installation prompts to install the plug-in. Note: You may have to close the web browser to finish the installation of the plug-in.
-
Page 30: Operating Via Guarding Vision App
5 Operating via Guarding Vision App Purpose: Guarding Vision is an application for mobile devices. With the App, you can view live image of the camera, receive alarm notification and so on. Note: Guarding Vision service is not supported by certain camera models. Enable Guarding Vision on Camera Purpose: Guarding Vision service should be enabled on your camera before... -
Page 31: Enable Guarding Vision Via Web Browser
“Privacy Policy” Service” Figure 5-1 Verification Code Setting (SADP) Note: The verification code is required when you add the camera to Guarding Vision app. 3. Click and read "Terms of Service" and "Privacy Policy". 4. Confirm the settings. 5.1.2 Enable Guarding Vision via Web Browser Before you start: You need to activate the camera before enabling the service. - Page 32 Steps: 1. Access the camera via web browser. Refer to Chapter 4. 2. Enter platform access configuration interface: Configuration > Network > Advanced Settings > Platform Access Guarding Vision dev.guardingvision.com Figure 5-2 Platform Access Configuration (Web) 3. Select Platform Access Mode as Guarding Vision. 4.
-
Page 33: Guarding Vision Setup
Guarding Vision Setup Steps: 1. Download and install the Guarding Vision app by searching “Guarding Vision” in App Store or Google Play 2. Launch the app and register for a Guarding Vision user account. 3. Log in Guarding Vision app after registration. Adding Camera to Guarding Vision Before you start: You need to enable the Guarding Vision service on camera before... - Page 34 You can find the QR code on the camera or on the cover of the Quick Start Guide of the camera in the package. Figure 5-4 Scan QR Code Note: If the QR code is missing or too blur to be recognized, you can also add the camera by tapping the icon and inputting the camera's serial number.
-
Page 35: Initializing The Memory Card
Initializing the Memory Card Steps: Check the memory card status by tapping on the Storage Status in the Device Settings interface. If the memory card status displays as Uninitialized, tap to initialize it. The status will then change to Normal. You can then start recording any event triggered video in the camera such as motion detection.
Need help?
Do you have a question about the IP4AFBIR150 and is the answer not in the manual?
Questions and answers