Scanlab RTC 4 Installation And Operation Manual page 133

get_serial_number (command) ......................... 85
get_startstop_info (command) ......................... 85
get_status (command) ....................................... 86
get_time (command) ......................................... 86
get_value (command) ........................................ 87
get_wait_status (command) .............................. 88
get_waveform (command) ................................ 88
get_xy_pos (command) ..................................... 88
goto_xy (command) ........................................... 89
guarantee ......................................................... 129
H
home jump mode ............................................... 89
home_position (command) ............................... 89
I
I/O extension board ............................................ 57
IEEE floating point format .................................. 72
image field
calibration factor ........................................ 29
coordinate range ................................ 29, 130
image field distortion .................................... 30–31
importing the RTC4 commands ..................... 62–63
initialization of RTC4 ........................................... 63
input resistance
digital input ports ..................................... 130
installation and start-up ................................ 58–62
DLL .............................................................. 62
hardware .................................................... 60
jumper settings ...................................... 58–60
integer, definition of data type ........................... 72
intelliSCAN
additional functions .................................... 38
querying data .............................................. 39
selecting data signals .................................. 38
J
jump commands ................................... 15, 90, 120
scan head and laser control ........................ 18
jump delay .......................................................... 17
optimizing ................................................... 27
variable jump delay ............................. 18, 104
jump speed ......................................................... 15
jump_abs (command) ........................................ 90
jump_rel (command) ......................................... 90
jumper settings .............................................. 58–60
L
lag ...................................................................... 17
lamp current ................................................. 34, 98
laser connectors
pin-out of 9-pin laser connector ................. 52
pin-out of laser extension connector ........... 53
laser control ................................................... 32–37
®
RTC 4 PC Interface Board
Rev. 1.3 e
Index
– during jump command ............................ 18
– during mark command ............................. 19
commands ........................................ 108, 116
lamp current ......................................... 34, 98
timing (CO mode) ...................................... 33
2
timing (laser mode 4) .................................. 37
timing (YAG modes) ............................... 34–36
laser delays ................................................. 16, 107
laser mode 4 laser control ................................... 37
laser safety .......................................................... 11
laser signals .................................................. 52, 53
TTL signal level ............................................ 59
laser_on_list (command) .................................... 91
laser_signal_off (command) .............................. 91
laser_signal_off_list (command) ....................... 91
laser_signal_on (command) ............................... 92
laser_signal_on_list (command) ........................ 92
LaserOff delay ..................................................... 17
optimizing ................................................... 26
LaserOn delay ..................................................... 17
optimizing ................................................... 26
layout
RTC4 with optical data interface ................... 9
standard version ........................................... 8
list buffers ........................................................... 12
capacity (max. number of commands) 12, 130
list change, automatic .................................. 13, 75
list commands .............................................. 12, 71
list_call (command) ............................................ 92
list_call_cond (command) .................................. 93
list_jump_cond (command) ............................... 93
list_nop (command) ........................................... 94
list_return (command) ....................................... 94
load_correction_file (command) ....................... 95
load_program_file (command) .......................... 96
load_varpolydelay (command) .......................... 97
long, definition of data type ............................... 72
long_delay (command) ...................................... 98
longint, definition of data type ........................... 72
M
manufacturer ........................................................ 6
mark commands ................................... 15, 98, 121
scan head and laser control ........................ 19
mark delay .......................................................... 19
optimizing ................................................... 27
mark_abs (command) ........................................ 98
mark_rel (command) .......................................... 98
marking speed .................................................... 15
marking time
measuring via RTC4 timer ........................... 16
measurement
status signals and output values ................. 38
measurement_status (command) ..................... 99
microsteps .......................................................... 15
output interval .......................................... 130
133