ComAp InteliNano NT MRS Fast User's Manual

ComAp,a.s.
Kundratka 2359/17
180 00, Praha 8
Czech Republic
InteliNano NT
Typical wiring diagram
DIESEL / GASOLINE ENGINE GENERATOR
G
ECU
D+
PC
Accessing the setup mode
Ensure the engine is stopped and the controller is in Manual mode (green LED above button
If you have not configured the custom initialization (init) screen then press and hold
If you have already created your own init screen then press and hold
▼
button. Then press to switch LCD to default init screen, and then press
To move up and down in the setup menu use
Engine parameters and protections
Outputs and inputs
Output
Output source
code
O00 Not Used
O01 Starter
O02 Fuel Solenoid
O03 Stop Solenoid
O04 Alarm
O07 Ready To Load
O08 Prestart
O09 ECU Power Relay
O10 Choke
O11 Glow Plugs
Normally Open Contact – output
Normally Closed Contact – output
User curves
I21
VDO Level % VDO 5 Bar
Datcon Level % VDO 10 Bar
Datcon 5 Bar
Datcon 7 Bar
Datcon 10 Bar
Not selected Not selected
InteliNano-NT MRS, SW version 1.5, ©ComAp – September 2013
InteliNano-NT-MRS-1.5-Fast User Guide.pdf

MRS
LOAD
L1
L2
L3
N
Stop
button and then briefly press
.
Auto
▲ ▼
Start
and buttons. Press button to select or
Basic settings
Generator protections
Output settings
Type Terminal assignment
binary T04, T05, T06, T07
binary T04
binary T04, T05, T06, T07
binary T04, T05, T06, T07
binary T04, T05, T06, T07
binary T04, T05, T06, T07
binary T04, T05, T06, T07
binary T04, T05, T06, T07
binary T04, T05, T06, T07
binary T04, T05, T06, T07
Normally Open Contact - input
button
Normally Closed Contact – input
button
I23 I25
VDO 40-120 °C
VDO 50-150 °C
Datcon High °C
Datcon Low °C
Not selected
Case dimensions: 118mm x108mm x 40mm
Panel Cutout: 96mm x 96mm
GENERATOR VOLTAGE
MEASUREMENT
T16 = Neutral
T17 = Phase 1
T18 = Phase 2
T19 = Phase 3
USB interface
INTPUT TERMINALS
T10 = COM for analog inputs
T11 = binary input
T12 = binary input
T13 = binary/analog input – Low Fuel Level
T14 = binary/analog input – Coolan Temperature
T15 = binary/analog input – Oil Pressure
W !
ARNING
If D+ is not used, connect this terminal to battery positive!
Auto
is turned off).
▲
Stop
button, then briefly press button and then
▲
, the custom init screen will appear, keep holding the
Stop
button for exit.
Input
Input source
code
I00 Not Used
I01 Emergency Stop
I02 Remote Start/Stop
I03 Remote Start And Load
I04 Access Lock
I07 GCB Feedback
I10 External Warning 1
I11 External Warning 2
I12 External Warning 3
I13 External Shutdown 1
I14 External Shutdown 2
I15 External Shutdown 3
I20 Low Fuel Level
I21 Fuel Level Analog
I22 Low Oil Pressure
I23 Oil Pressure Analog
I24 High Coolant Temperature
I25 Coolant Temperature Analog
I29 Fuel Level SD
1
Fast User Guide
Dimensions
CAN INTERFACE
POWER SUPPLY, D+
T01 = BATT -
T02 = D+
T03 = BATT +
OUTPUT TERMINALS
T04 = binary output – Starter (6A)
T05 = binary output - Fuel Solenoid (6A)
T06 = binary output (500 mA)
T07 = binary input/output (500 mA)
.
Auto
Stop
Input settings
ECU setting
Info
Type Terminal assignment
binary T07, T11, T12, T13, T14, T15
binary T07, T11, T12, T13, T14, T15
binary T11
binary T11
binary T07, T11, T12, T13, T14, T15
binary T07, T11, T12, T13, T14, T15
binary T07, T11, T12, T13, T14, T15
binary T07, T11, T12, T13, T14, T15
binary T07, T11, T12, T13, T14, T15
binary T07, T11, T12, T13,T14, T15
binary T07, T11, T12, T13, T14, T15
binary T07, T11, T12, T13, T14, T15
binary T07, T11, T12, T13, T14, T15
analog T13, T14, T15
binary T07, T11, T12, T13, T14, T15
analog T13, T14, T15
binary T07, T11, T12, T13, T14, T15
analog T13, T14, T15
Binary T07, T11, T12, T13, T14, T15
L
COM
H